欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADCMP553
廠商: Analog Devices, Inc.
英文描述: Single Supply High Speed PECL Comparators
中文描述: 單電源高速PECL的比較
文件頁數: 11/14頁
文件大小: 522K
代理商: ADCMP553
Preliminary Technical Data
ADCMP551/ADCMP552/ADCMP553
APPLICATION INFORMATION
The ADCMP55x series of comparators are very high speed
devices. Consequently, high speed design techniques must be
employed to achieve the best performance. The most critical
aspect of any ADCMP55x design is the use of a low impedance
ground plane. A ground plane, as part of a multilayer board, is
recommended for proper high speed performance. Using a
continuous conductive plane over the surface of the circuit
board can create this, allowing breaks in the plane only for
necessary signal paths. The ground plane provides a low
inductance ground, eliminating any potential differences at
different ground points throughout the circuit board caused by
ground bounce. A proper ground plane also minimizes the
effects of stray capacitance on the circuit board.
Rev. PrB | Page 11 of 14
It is also important to provide bypass capacitors for the power
supply in a high speed application. A 1 μF electrolytic bypass
capacitor should be placed within 0.5 inches of each power
supply pin to ground. These capacitors reduce any potential
voltage ripples from the power supply. In addition, a 10 nF
ceramic capacitor should be placed as close to the power supply
pins as possible on the ADCMP55x to ground. These capacitors
act as a charge reservoir for the device during high frequency
switching.
The LATCH ENABLE input is active low (latched). If the
latching function is not used, the LATCH ENABLE input pins
may be left open. The internal pull-ups on the latch pins set the
latch to transparent mode. If the latch is to be used, valid PECL
voltages are required on the inputs for proper operation. The
PECL voltages should be referenced to V
CCI
.
Occasionally, one of the two comparator stages within the
ADCMP551/ADCMP552 is not used. The inputs of the unused
comparator should not be allowed to float. The high internal
gain may cause the output to oscillate (possibly affecting the
comparator that is being used) unless the output is forced into a
fixed state. This is easily accomplished by ensuring that the two
inputs are at least one diode drop apart, while also appropriately
connecting the LATCH ENABLE and LATCH ENABLE inputs
as described previously.
The best performance is achieved with the use of proper PECL
terminations. The open-emitter outputs of the ADCMP55x are
designed to be terminated through 50 resistors to
V
CCO
2.0 V or any other equivalent PECL termination. If high
speed PECL signals must be routed more than a centimeter,
microstrip or stripline techniques may be required to ensure
proper transition times and prevent output ringing.
CLOCK TIMING RECOVERY
Comparators are often used in digital systems to recover clock
timing signals. High speed square waves transmitted over a
distance, even tens of centimeters, can become distorted due to
stray capacitance and inductance. Poor layout or improper
termination can also cause reflections on the transmission line,
further distorting the signal waveform. A high speed
comparator can be used to recover the distorted waveform
while maintaining a minimum of delay.
OPTIMIZING HIGH SPEED PERFORMANCE
As with any high speed comparator amplifier, proper design
and layout techniques should be used to ensure optimal
performance from the ADCMP55x. The performance limits of
high speed circuitry can easily be a result of stray capacitance,
improper ground impedance, or other layout issues.
Minimizing resistance from source to the input is an important
consideration in maximizing the high speed operation of the
ADCMP55x. Source resistance in combination with equivalent
input capacitance can cause a lagged response at the input, thus
delaying the output. The input capacitance of the ADCMP55x,
in combination with stray capacitance from an input pin to
ground, could result in several picofarads of equivalent
capacitance. A combination of 3 k source resistance and 5 pF
input capacitance yields a time constant of 15 ns, which is
significantly slower than the 750 ps capability of the
ADCMP55x. Source impedances should be significantly less
than 100 for best performance.
Sockets should be avoided due to stray capacitance and induc-
tance. If proper high speed techniques are used, the
ADCMP55x should be free from oscillation when the
comparator input signal passes through the switching threshold.
COMPARATOR PROPAGATION DELAY
DISPERSION
The ADCMP55x has been specifically designed to reduce
propagation delay dispersion over an input overdrive range of
100 mV to 1 V. Propagation delay overdrive dispersion is the
change in propagation delay that results from a change in the
degree of overdrive (how far the switching point is exceeded by
the input). The overall result is a higher degree of timing
accuracy since the ADCMP55x is far less sensitive to input
variations than most comparator designs.
相關PDF資料
PDF描述
ADCMP553BRM Single Supply High Speed PECL Comparators
ADCMP561 Dual High Speed PECL Comparators
ADCMP561BRQ Dual High Speed PECL Comparators
ADCMP562 Dual High Speed PECL Comparators
ADCMP562BRQ Dual High Speed PECL Comparators
相關代理商/技術參數
參數描述
ADCMP553BRM 制造商:Analog Devices 功能描述:Comparator Single 5.25V 8-Pin MSOP 制造商:Analog Devices 功能描述:COMPARATOR SGL 5.25V 8MSOP - Rail/Tube 制造商:Analog Devices 功能描述:3.3V to 5V 1 0.75ns Rp[^ 8MSOP Tube 制造商:Analog Devices 功能描述:IC COMPARATOR HIGH SPEED
ADCMP553BRMZ 功能描述:IC COMPARATOR PECL/LVPECL 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 標準包裝:1 系列:- 類型:通用 元件數:1 輸出類型:CMOS,開路集電極,TTL 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V 電壓 - 輸入偏移(最小值):7mV @ 5V 電流 - 輸入偏壓(最小值):0.25µA @ 5V 電流 - 輸出(標準):84mA @ 5V 電流 - 靜態(最大值):120µA CMRR, PSRR(標準):- 傳輸延遲(最大):600ns 磁滯:- 工作溫度:-40°C ~ 85°C 封裝/外殼:SC-74A,SOT-753 安裝類型:表面貼裝 包裝:剪切帶 (CT) 產品目錄頁面:1268 (CN2011-ZH PDF) 其它名稱:*LMV331M5*LMV331M5/NOPBLMV331M5CT
ADCMP553BRMZ 制造商:Analog Devices 功能描述:IC, HIGH SPEED COMP, SINGLE, 500PS MSOP8
ADCMP561 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual High Speed PECL Comparators
ADCMP561BRQ 功能描述:IC COMP PECL DUAL HS 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS,推挽式,滿擺幅,TTL 電壓 - 電源,單路/雙路(±):2.5 V ~ 5.5 V,±1.25 V ~ 2.75 V 電壓 - 輸入偏移(最小值):5mV @ 5.5V 電流 - 輸入偏壓(最小值):1pA @ 5.5V 電流 - 輸出(標準):- 電流 - 靜態(最大值):24µA CMRR, PSRR(標準):80dB CMRR,80dB PSRR 傳輸延遲(最大):450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA,CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586
主站蜘蛛池模板: 辉县市| 江永县| 台江县| 景洪市| 方正县| 淮安市| 象州县| 堆龙德庆县| 广平县| 牡丹江市| 宁乡县| 义乌市| 铁岭县| 桃源县| 德江县| 扶余县| 临沭县| 泰顺县| 天全县| 扎鲁特旗| 蒲江县| 兴和县| 新巴尔虎左旗| 盖州市| 武夷山市| 库车县| 新巴尔虎左旗| 南昌市| 伊金霍洛旗| 孙吴县| 祁连县| 三门县| 交口县| 板桥市| 澄迈县| 乐山市| 磐安县| 合江县| 华蓥市| 汉阴县| 喀喇沁旗|