- 您現在的位置：買賣IC網 > PDF目錄373977 > ADCMP572BCP-WP (ANALOG DEVICES INC) Ultrafast 3.3 V/5 V Single-Supply SiGe Comparators PDF資料下載
參數資料
| 型號： | ADCMP572BCP-WP |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Ultrafast 3.3 V/5 V Single-Supply SiGe Comparators |
| 中文描述： | COMPARATOR, 5000 uV OFFSET-MAX, 0.165 ns RESPONSE TIME, QCC16 |
| 封裝： | 3 X 3 MM, MO-220-VEED-2, LFCSP-16 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 381K |
| 代理商： | ADCMP572BCP-WP |
ADCMP572/ADCMP573
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often desirable in a
noisy environment or when the differential input amplitudes are
relatively small or slow moving, but excessive hysteresis has a
cost in degraded accuracy and slew-induced timing shifts. The
transfer function for a comparator with hysteresis is shown in
Figure 19. If the input voltage approaches the threshold (0.0 V
in this example) from the negative direction, the comparator
switches from low to high when the input crosses +VH/2. The
new switching threshold becomes V
H
/2. The comparator
remains in the high state until the threshold V
H
/2 is crossed
from the positive direction. In this manner, noise centered on
0.0 V input does not cause the comparator to switch states
unless it exceeds the region bounded by ±V
H
/2.
Rev. 0 | Page 11 of 16
OUTPUT
INPUT
0
V
OL
V
OH
+V
H
2
–V
H
2
0
Figure 19. Comparator Hysteresis Transfer Function
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to the
input. A limitation of this approach is that the amount of
hysteresis varies with the output logic levels, resulting in
hysteresis that can be load dependent and is not symmetrical
about the threshold. The external feedback network can also
introduce significant parasitics, which reduce high speed
performance and can even induce oscillation in some cases.
The ADCMP572/ADCMP573 comparators offer a program-
mable hysteresis feature that can significantly improve the
accuracy and stability of the desired hysteresis. By connecting
an external pull-down resistor from the HYS pin to GND, a
variable amount of hysteresis can be applied. Leaving the HYS
pin disconnected disables the feature, and hysteresis is then less
than 1 mV as specified. The maximum hysteresis that can be
applied using this method is approximately ±25 mV with the
pin grounded. Figure 20 illustrates the amount of hysteresis
applied as a function of external resistor value. The advantages
of applying hysteresis in this manner are improved accuracy,
stability, and reduced component count. An external bypass
capacitor is not recommended on the HYS pin because it would
likely degrade the jitter performance of the device. The
hysteresis pin could also be driven by a CMOS DAC. It is biased
to approximately 250 mV and has an internal series resistance
of 600 .
0
10
20
30
40
50
60
H
2
3
0
1
4
5
6
R
HYS
(k
)
0
Figure 20. Hysteresis vs. R
HYS
Control Resistor
MINIMUM INPUT SLEW RATE REQUIREMENTS
As with all high speed comparators, a minimum slew rate
requirement must be met to ensure that the device does not
oscillate as the input signal crosses the threshold. This
oscillation is due in part to the high input bandwidth of the
comparator and the feedback parasitics inherent in the package.
A minimum slew rate of 50 V/μs should ensure clean output
transitions from the ADCMP572/ ADCMP573 comparators.
The slew rate may be too slow for other reasons. The extremely
high bandwidth of these devices means that broadband noise
can be a significant factor when input slew rates are low. There
will be at least 120 μv of thermal noise generated over the full
comparator bandwidth by two 50 terminations at room
temperature. With a slew rate of only 50 V/μs the input will be
inside this noise band for over 2 ps, rendering the comparator’s
jitter performance of 200 fs moot. Raising the slew rate of the
input signal and/or reducing the bandwidth over which this
resistance is seen at the input can greatly reduce jitter.
相關PDF資料 |
PDF描述 |
|---|---|
| ADCMP573BCP-R2 | Ultrafast 3.3 V/5 V Single-Supply SiGe Comparators |
| ADCMP573BCP-RL7 | Ultrafast 3.3 V/5 V Single-Supply SiGe Comparators |
| ADCMP573BCP-WP | Ultrafast 3.3 V/5 V Single-Supply SiGe Comparators |
| ADCMP572 | Ultrafast 3.3 V Single-Supply Comparators |
| ADCMP572BCP | Ultrafast 3.3 V Single-Supply Comparators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADCMP572BCPZ-R2 | 功能描述:IC COMPARATOR CML 3.3-5V 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 標準包裝:1 系列:- 類型:通用 元件數:1 輸出類型:CMOS，開路集電極，TTL 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:7mV @ 5V 電流 - 輸入偏壓（最小值）:0.25µA @ 5V 電流 - 輸出（標準）:84mA @ 5V 電流 - 靜態(tài)（最大值）:120µA CMRR, PSRR（標準）:- 傳輸延遲（最大）:600ns 磁滯:- 工作溫度:-40°C ~ 85°C 封裝/外殼:SC-74A，SOT-753 安裝類型:表面貼裝 包裝:剪切帶 (CT) 產品目錄頁面:1268 (CN2011-ZH PDF) 其它名稱:*LMV331M5*LMV331M5/NOPBLMV331M5CT |
| ADCMP572BCPZ-RL7 | 功能描述:IC COMPARATOR CML 3.3-5V 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態(tài)（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| ADCMP572BCPZ-WP | 功能描述:IC COMPARATOR CML 3.3-5V 16LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:帶電壓基準 元件數:4 輸出類型:開路漏極 電壓 - 電源，單路/雙路(±):2.5 V ~ 11 V，±1.25 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態(tài)（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:- 磁滯:- 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 安裝類型:表面貼裝 包裝:管件 產品目錄頁面:1386 (CN2011-ZH PDF) |
| ADCMP572XCP | 制造商:Analog Devices 功能描述:CML ULTRAFAST 3.3V SINGLE SUPPLY COMPARATOR - Bulk |
| ADCMP573 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultrafast 3.3 V Single-Supply Comparators |
發(fā)布緊急采購，3分鐘左右您將得到回復。