- 您現在的位置：買賣IC網 > PDF目錄373980 > ADE7753ARSRL (ANALOG DEVICES INC) Active and Apparent Energy Metering IC with di/dt sensor interface PDF資料下載
參數資料
| 型號： | ADE7753ARSRL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Active and Apparent Energy Metering IC with di/dt sensor interface |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | MO-150AE, SSOP-20 |
| 文件頁數： | 34/38頁 |
| 文件大?。?/td> | 449K |
| 代理商： | ADE7753ARSRL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁
ADE7753
–34–
REV. PrF 10/02
PRELIMINARY TECHNICAL DATA
Interrupt Status Register (0BH) / Reset Interrupt Status Register (0CH) /Interrupt E nable Register (0Ah)
T he Status Register is used by the MCU to determine the source of an interrupt request (
IRQ
). When an interrupt event occurs
in the ADE7753, the corresponding flag in the Interrupt Status register is set logic high. If the enable bit for this flag is logic
one in the Interrupt Enable register, the
IRQ
logic output goes active low. When the MCU services the interrupt it must first
carry out a read from the Interrupt Status Register to determine the source of the interrupt.
T able VII: Interrupt Status Register, Reset Interrupt Status Register & Interrupt E nable Register
Interrupt
F lag
Description
Bit
L ocation
0h
A E H F
Indicates that an interrupt was caused by the 0 to 1 transition of the MSB of the Active
Energy register (i.e. the AENERGY register is half full)
Indicates that an interrupt was caused by a SAG on the line voltage or no zero crossings were
detected.
Indicates the end of energy accumulation over an integer number of half line cycles as
defined by the content of the LINECYC Register—see
Line Cycle Energy Accumulation Mode
Indicates that new data is present in the Waveform Register.
T his status bit reflects the status of the ZX logic ouput—see
Zero Crossing Detection
Indicates that a temperature conversion result is available in the T emperature Register.
Indicates the end of a reset (for both software or hardware reset). T he corresponding
enable bit has no function in the Interrupt Enable Register, i.e. this status bit is set at
the end of a reset, but it cannot be enabled to cause an interrupt.
Indicates that the Active Energy register has overflowed.
Indicates that waveform sample from Channel2 has exceeded the VPK LVL value.
Indicates that waveform sample from Channel1 has exceeded the IPK LVL value.
Indicates that an interrupt was caused by the 0 to 1 transition of the MSB of the Apparent
Energy register (i.e. the VAENERGY register is half full)
Indicates that the Apparent Enrgy register has overflowed.
Indicates that an interrupt was caused by a missing zero crossing on the line voltage for the
specified number of line cycles—see
Zero Crossing Time Out
Indicates that the power has gone from negative to positive.
Indicates that the power has gone from positive to negative.
Reserved
1h
SA G
2h
C Y C E N D
3h
4h
5h
6h
W SM P
Z X
T E M P
R E SE T
7h
8h
9h
Ah
A E OF
PK V
PK I
V AE H F
Bh
C h
V A E OF
Z X T O
D h
E h
F h
PPOS
PN E G
R E SE R V E D
相關PDF資料 |
PDF描述 |
|---|---|
| ADE7754 | ADE7754 |
| ADE7754AR | ADE7754 |
| ADE7754ARRL | ADE7754 |
| ADE7755AN-REF | Energy Metering IC with Pulse Output |
| ADE7755ARSRL | Energy Metering IC with Pulse Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7753ARSZ | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:ENERGY METERING IC |
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION METER |
| ADE7753ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7753-ARSZRL | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。