欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADE7768AR
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
中文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
封裝: PLASTIC, MS-012-AC, SOIC-16
文件頁數: 16/20頁
文件大小: 299K
代理商: ADE7768AR
ADE7768
When selecting a suitable F
1–4
frequency for a meter design, the
frequency output at I
MAX
(maximum load) with a meter constant
of 100 imp/kWh should be compared with Column 4 of
Table 9. The closest frequency in Table 9 determines the best
choice of frequency (F
1–4
). For example, if a meter with a max-
imum current of 25 A is being designed, the output frequency
on F1 and F2 with a meter constant of 100 imp/kWh is 0.153 Hz
at 25 A and 220 V (from Table 8). In Table 9, the closest fre-
quency to 0.153 Hz in Column 4 is 0.176 Hz. Therefore, as
shown in Table 5, F3 (3.43 Hz) is selected for this design.
Rev. A | Page 16 of 20
Frequency Outputs
Figure 2 shows a timing diagram for the various frequency
outputs. The F1 and F2 outputs are the low frequency outputs
that can be used to directly drive a stepper motor or electro-
mechanical impulse counter. The F1 and F2 outputs provide
two alternating low frequency pulses. The F1 and F2 pulse
widths (t
1
) are set such that if they fall below 240 ms (0.24 Hz),
they are set to half of their period. The maximum output
frequencies for F1 and F2 are shown in Table 6.
The high frequency CF output is intended for communications
and calibration purposes. CF produces a 90-ms-wide active
high pulse (t
4
) at a frequency proportional to active power. The
CF output frequencies are given in Table 7. As with F1 and F2,
if the period of CF (t
5
) falls below 180 ms, the CF pulse width is
set to half the period. For example, if the CF frequency is 20 Hz,
the CF pulse width is 25 ms.
When high frequency mode is selected (SCF = 0, S1 = S0 = 1),
the CF pulse width is fixed at 35 μs. Therefore, t
4
is always 35 μs,
regardless of output frequency on CF.
NO-LOAD THRESHOLD
The ADE7768 includes a no-load threshold and start-up
current feature that eliminates any creep effects in the meter.
The ADE7768 is designed to issue a minimum output
frequency. Any load generating a frequency lower than this
minimum frequency does not cause a pulse to be issued on F1,
F2, or CF. The minimum output frequency is given as 0.00244%
for each of the F
1–4
frequency selections (see Table 5).
For example, for an energy meter with a meter constant of
100 imp/kWh on F1, F2 using F
3
(3.43 Hz), the minimum
output frequency at F1 or F2 would be 0.00244% of 3.43 Hz or
8.38 × 10
–5
Hz. This would be 2.68 × 10
–3
Hz at CF (32 × F1 Hz)
when SCF = S0 = 1, S1 = 0. In this example, the no-load
threshold would be equivalent to 3 W of load or a start-up
current of 13.72 mA at 220 V. Compare this value to the
IEC62053-21 specification which states that the meter must
start up with a load equal to or less than 0.4% Ib. For a 5 A (Ib)
meter, 0.4% of Ib is equivalent to 20 mA.
NEGATIVE POWER INFORMATION
The ADE7768 detects when the current and voltage channels
have a phase shift greater than 90°. This mechanism can detect
an incorrect meter connection or the generation of negative
power. The REVP pin output goes active high when negative
power is detected and active low if positive power is detected.
The REVP pin output changes state as a pulse is issued on CF.
EVALUATION BOARD AND REFERENCE DESIGN
BOARD
An evaluation board can be used to verify the functionality and
the performance of the ADE7768. Download documentation
for the board from
http://www.analog.com/ADE7768.
In addition, the reference design board ADE7768ARN-REF
and Application Note AN-679 can be used in the design
of a low cost watt-hour meter that surpasses IEC62053-21
accuracy specifications. Download the application note from
http://www.analog.com/ADE7768.
相關PDF資料
PDF描述
ADE7768AR-REF Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADE7768AR-RL Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADE7768ARZ Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADE7768ARZ-RL Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADEL2020AN Improved Second Source to the EL2020
相關代理商/技術參數
參數描述
ADE7768AR-REF 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADE7768AR-RL 制造商:Analog Devices 功能描述:ENERGY MEASUREMENT 16SOIC - Tape and Reel
ADE7768ARZ 功能描述:IC ENERGY METERING 1PHASE 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7768ARZ-RL 功能描述:IC ENERGY METERING 1PHASE 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7769 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and No-Load Indication
主站蜘蛛池模板: 泾川县| 昭平县| 高碑店市| 甘孜| 温宿县| 应用必备| 汤原县| 诸暨市| 定兴县| 峨边| 沾益县| 石狮市| 建阳市| 杂多县| 阳东县| 安庆市| 嵩明县| 四子王旗| 广汉市| 前郭尔| 邯郸县| 将乐县| 五华县| 江华| 喀什市| 石泉县| 楚雄市| 岑巩县| 恭城| 崇信县| 红河县| 德阳市| 安吉县| 文水县| 石河子市| 自治县| 廉江市| 昆山市| 措勤县| 武城县| 房产|