欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADE7768ARZ
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
中文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
封裝: LEAD FREE, PLASTIC, MS-012-AC, SOIC-16
文件頁數: 7/20頁
文件大小: 299K
代理商: ADE7768ARZ
ADE7768
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Rev. A | Page 7 of 20
V
DD
V2P
1
2
V2N
3
V1N
4
F1
16
F2
15
CF
14
DGND
13
V1P
5
REVP
12
AGND
6
RCLKIN
11
REF
IN/OUT
7
S0
10
SCF
8
S1
9
ADE7768
TOP VIEW
(Not to Scale)
0
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
1
V
DD
Description
Power Supply. This pin provides the supply voltage for the circuitry in the ADE7768. The supply voltage
should be maintained at 5 V ± 5% for specified operation. This pin should be decoupled with a 10 μF
capacitor in parallel with a 100 nF ceramic capacitor.
Analog Inputs for Channel V2 (Voltage Channel). These inputs provide a fully differential input pair. The
maximum differential input voltage is ±165 mV for specified operation. Both inputs have internal ESD
protection circuitry; an overvoltage of ±6 V can be sustained on these inputs without risk of permanent
damage.
Analog Inputs for Channel V1 (Current Channel). These inputs are fully differential voltage inputs with a
maximum signal level of ±30 mV with respect to the V1N pin for specified operation. Both inputs have
internal ESD protection circuitry and, in addition, an overvoltage of ±6 V can be sustained on these inputs
without risk of permanent damage.
This pin provides the ground reference for the analog circuitry in the ADE7768, that is, the ADCs and
reference. This pin should be tied to the analog ground plane of the PCB. The analog ground plane is the
ground reference for all analog circuitry, such as antialiasing filters, current and voltage sensors, and so forth.
For accurate noise suppression, the analog ground plane should be connected to the digital ground plane at
only one point. A star ground configuration helps to keep noisy digital currents away from the analog
circuits.
This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal value of 2.45 V
and a typical temperature coefficient of 20 ppm/°C. An external reference source may also be connected at
this pin. In either case, this pin should be decoupled to AGND with a 1 μF tantalum capacitor and a 100 nF
ceramic capacitor. The internal reference cannot be used to drive an external load.
Select Calibration Frequency. This logic input is used to select the frequency on the calibration output CF.
See Table 7.
These logic inputs are used to select one of four possible frequencies for the digital-to-frequency conversion.
With this logic input, designers have greater flexibility when designing an energy meter. See the Selecting a
Frequency for an Energy Meter Application section.
To enable the internal oscillator as a clock source to the chip, a precise low temperature drift resistor at a
nominal value of 6.2 kΩ must be connected from this pin to DGND.
This logic output goes high when negative power is detected, that is, when the phase angle between the
voltage and current signals is greater than 90°. This output is not latched and is reset when positive power is
once again detected. The output goes high or low at the same time that a pulse is issued on CF.
This pin provides the ground reference for the digital circuitry in the ADE7768, that is, the multiplier, filters,
and digital-to-frequency converter. This pin should be tied to the digital ground plane of the PCB. The digital
ground plane is the ground reference for all digital circuitry, such as counters (mechanical and digital), MCUs,
and indicator LEDs. For accurate noise suppression, the analog ground plane should be connected to the
digital ground plane at one point only—a star ground.
Calibration Frequency Logic Output. The CF logic output provides instantaneous, positive-only real power
information. This output is intended for calibration purposes. See the SCF pin description.
Low Frequency Logic Outputs. F1 and F2 supply average positive-only real power information. The logic
outputs can be used to directly drive electromechanical counters and 2-phase stepper motors. See the
Transfer Function section.
2, 3
V2P, V2N
4, 5
V1N, V1P
6
AGND
7
REF
IN/OUT
8
SCF
9, 10
S1, S0
11
RCLKIN
12
REVP
13
DGND
14
CF
15, 16
F2, F1
相關PDF資料
PDF描述
ADE7768ARZ-RL Energy Metering IC with Integrated Oscillator and Positive Power Accumulation
ADEL2020AN Improved Second Source to the EL2020
ADEL2020AR-20 Circular Connector Cable Assembly; Connector Type A:Circular Plug; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes
ADEL2020AR-20-REEL Circular Connector Cable Assembly; Connector Type A:Circular Plug; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes
ADF4001BRU 200 MHz Clock Generator PLL
相關代理商/技術參數
參數描述
ADE7768ARZ-RL 功能描述:IC ENERGY METERING 1PHASE 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7769 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and No-Load Indication
ADE7769AR 制造商:Analog Devices 功能描述:Energy Measurement 16-Pin SOIC N
ADE7769AR-REF 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and No-Load Indication
ADE7769AR-RL 制造商:Analog Devices 功能描述:Energy Measurement 16-Pin SOIC N T/R 制造商:Analog Devices 功能描述:ENERGY MEASUREMENT 16SOIC - Tape and Reel
主站蜘蛛池模板: 广灵县| 普格县| 茶陵县| 北京市| 阿图什市| 玛曲县| 南部县| 博爱县| 封开县| 多伦县| 商都县| 都匀市| 丰台区| 化隆| 台东市| 邯郸县| 平塘县| 兴国县| 元谋县| 溧阳市| 华池县| 东辽县| 若尔盖县| 大田县| 霍州市| 龙川县| 交口县| 东台市| 搜索| 南昌市| 资中县| 丹寨县| 克东县| 洛隆县| 南开区| 玉门市| 雷山县| 孟津县| 连云港市| 和平区| 清苑县|