- 您現在的位置：買賣IC網 > PDF目錄373993 > ADL5385 (Analog Devices, Inc.) 300 MHz to 1000 MHz Quadrature Modulator PDF資料下載
參數資料
| 型號： | ADL5385 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 300 MHz to 1000 MHz Quadrature Modulator |
| 中文描述： | 300 MHz到1000 MHz的正交調制器 |
| 文件頁數： | 12/20頁 |
| 文件大小： | 904K |
| 代理商： | ADL5385 |
ADL5370
OPTIMIZATION
The carrier feedthrough and sideband suppression performance
of the ADL5370 can be improved through the use of optimiza-
tion techniques.
Carrier Feedthrough Nulling
Carrier feedthrough results from minute dc offsets that occur
between each of the differential baseband inputs. In an ideal
modulator the quantities (V
IOPP
V
IOPN
) and (V
QOPP
V
QOPN
) are
equal to zero, and this results in no carrier feedthrough. In a real
modulator, those two quantities are nonzero; and, when mixed
with the LO, they result in a finite amount of carrier feedthrough.
The ADL5370 is designed to provide a minimal amount of carrier
feedthrough. Should even lower carrier feedthrough levels be
required, minor adjustments can be made to the (V
IOPP
V
IOPN
)
and (V
QOPP
V
QOPN
) offsets. The I-channel offset is held constant
while the Q-channel offset is varied, until a minimum carrier
feedthrough level is obtained. The Q-channel offset required to
achieve this minimum is held constant while the offset on the I-
channel is adjusted, until a new minimum is reached. Through
two iterations of this process, the carrier feedthrough can be
reduced to as low as the output noise. The ability to null is
sometimes limited by the resolution of the offset adjustment.
Figure 26 shows the relationship of carrier feedthrough vs. dc
offset as null.
Rev. 0 | Page 12 of 20
–60
–88
–84
–80
–76
–72
–68
–64
–300 –240 –180 –120
–60
0
60
120
180
240
300
0
C
V
P
–V
N
OFFSET (μV)
Figure 26. Carrier Feedthrough vs. DC Offset Voltage at 450 MHz
Note that throughout the nulling process, the dc bias for the
baseband inputs remains at 500 mV. When no offset is applied
V
IOPP
=
V
IOPN
= 500 mV, or
V
IOPP
V
IOPN
=
V
IOS
= 0 V
When an offset of +V
IOS
is applied to the I-channel inputs
V
IOPP
= 500 mV +
V
IOS
/2, and
V
IOPN
= 500 mV
V
IOS
/2, such that
V
IOPP
V
IOPN
=
V
IOS
The same applies to the Q channel.
It is often desirable to perform a one-time carrier null calibra-
tion. This is usually performed at a single frequency. Figure 27
shows how carrier feedthrough varies with LO frequency over a
range of ±50 MHz on either side of a null at 450 MHz.
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
400
410
420
430
440
450
460
470
480
490
500
0
C
LO FREQUENCY (MHz)
Figure 27. Carrier Feedthrough vs. Frequency After Nulling at 450 MHz
Sideband Suppression Optimization
Sideband suppression results from relative gain and relative
phase offsets between the I and Q channels and can be
suppressed through adjustments to those two parameters.
Figure 28 illustrates how sideband suppression is affected by the
gain and phase imbalances.
0dB
0.0125dB
0.025dB
0.05dB
0.125dB
0.25dB
0.5dB
1.25dB
2.5dB
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0.01
0.1
1
10
100
0
S
PHASE ERROR (Degrees)
Figure 28. Sideband Suppression vs. Quadrature Phase Error for Various
Quadrature Amplitude Offsets
Figure 28 underlines the fact that adjusting only one parameter
improves the sideband suppression only to a point, unless the
other parameter is also adjusted. For example, if the amplitude
offset is 0.25 dB, improving the phase imbalance better than 1°
does not yield any improvement in the sideband suppression. For
optimum sideband suppression, an iterative adjustment
between phase and amplitude is required.
The sideband suppression nulling can be performed either through
adjusting the gain for each channel or through the modification
of the phase and gain of the digital data coming from the digital
signal processor.
相關PDF資料 |
PDF描述 |
|---|---|
| ADL5370 | 300 MHz to 1000 MHz Quadrature Modulator |
| ADL5370ACPZ-R2 | 300 MHz to 1000 MHz Quadrature Modulator |
| ADL5370ACPZ-R7 | 300 MHz to 1000 MHz Quadrature Modulator |
| ADL5370ACPZ-WP | 300 MHz to 1000 MHz Quadrature Modulator |
| ADL5370-EVALZ | 300 MHz to 1000 MHz Quadrature Modulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADL5385ACP | 制造商:Analog Devices 功能描述:IC QUAD MOD 50-2200MHZ 24LFCSP 制造商:Analog Devices 功能描述:IC, QUAD, MOD, 50-2200MHZ, 24LFCSP 制造商:Analog Devices 功能描述:IC, QUAD, MOD, 50-2200MHZ, 24LFCSP; Frequency Min:50MHz; Frequency Max:6GHz; RF Type:Quadrature; Supply Voltage Min:4.75V; Supply Voltage Max:5.5V; RF IC Case Style:LFCSP; No. of Pins:24; Operating Temperature Min:-40C; Operating ;RoHS Compliant: Yes |
| ADL5385ACPZ-R2 | 制造商:Analog Devices 功能描述: |
| ADL5385ACPZ-R7 | 功能描述:IC QUADRATURE MOD 50MHZ 24LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 調制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:調制器 LO 頻率:700MHz ~ 2.3GHz RF 頻率:700MHz ~ 2.3GHz P1dB:1dBm 底噪:-148dBm/Hz 輸出功率:-1dBm 電流 - 電源:46mA 電源電壓:2.7 V ~ 3.6 V 測試頻率:1.75GHz 封裝/外殼:28-WFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ADL5385ACPZ-WP | 制造商:Analog Devices 功能描述:Quadrature Mod 500MHz 24-Pin LFCSP EP 制造商:Analog Devices 功能描述:QUADRATURE MOD 500MHZ 24LFCSP - Waffle Pack |
| ADL5385-DIFFLO-EBZ | 功能描述:EVAL BOARD FOR ADL5385 制造商:analog devices inc. 系列:- 零件狀態:過期 類型:調制器 頻率:30MHz ~ 2.2GHz 配套使用產品/相關產品:ADL5385 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。