- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM101EARM (ANALOG DEVICES INC) Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:26; Connector Shell Size:17; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No PDF資料下載
參數資料
| 型號： | ADM101EARM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:26; Connector Shell Size:17; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
| 中文描述： | LINE TRANSCEIVER, PDSO10 |
| 封裝： | MICRO, SOIC-10 |
| 文件頁數： | 5/6頁 |
| 文件大小： | 64K |
| 代理商： | ADM101EARM |
REV. 0
ADM101E
–5–
GENERAL DESCRIPTION
The ADM101E is an RS-232 compatible line driver/receiver in
the Analog Devices Craft Port
series, containing one driver (trans-
mitter) and one receiver. It is ideal for serial communication in
small portable devices such as mobile telephones, palmtop per-
sonal computers and personal digital assistants, where a full,
RS-232 serial interface is not required, and only Tx and Rx lines
are required for low speed communication between devices. The
ADM101E operates from a single, +5 V supply, and generates
its own, on-chip, –5 V power supply, thus removing the need for
a negative power supply for the driver.
CIRCUIT DESCRIPTION
The internal circuitry consists of three main sections. These are:
1. A charge pump dc-to-dc converter.
2. 5 V logic to EIA-232 driver.
3. EIA-232 to 5 V logic receiver.
Charge Pump DC-DC Converter
The dc-dc converter generates a negative supply voltage from
the +5 V supply, thus removing the need for a separate –5 V
rail. It consists of an on-chip 200 kHz oscillator, switching ma-
trix and two external capacitors, as shown in Figure 7.
INTERNAL
OSCILLATOR
GND
C2
C1
S1
S2
S3
S4
V
CC
GND
V– = –V
CC
+
+
Figure 7. Charge Pump DC–DC Converter
When S1 and S2 are closed, S3 and S4 are open, and C1
charges to +V
CC
. S1 and S2 are then opened, while S3 and S4
are closed to connect C1 across C2, dumping charge into C2.
Since the positive terminal of C2 is at ground, a negative voltage
will be built up on its negative terminal with each cycle of the
oscillator. This voltage depends on the current drawn from C2.
If the current is small, the voltage will be close to –V
CC
, but will
fall as the current drawn increases.
Charge Pump Capacitors And Supply Decoupling
For proper operation of the charge pump, the capacitors should
have an equivalent series resistance (ESR) less than 1
. As the
charge pump draws current pulses from V
CC
, the V
CC
decou-
pling capacitor should also have low ESR. The V
CC
decoupling
capacitor and V– reservoir capacitor should also have low ESR
because they determine how effectively ESD pulses are clamped
to V
CC
or V– by the on-chip clamp diodes. Tantalum or mono-
lithic ceramic capacitors are suitable for these components. If
using tantalum capacitors, do not forget to observe polarity.
Transmitter (Driver) Section
The driver converts 5 V logic input levels into RS-232 compat-
ible output levels. With V
CC
= +5 V and driving an EIA-232
load, the output voltage swing is typically
±
4.2 V.
Receiver Section
The receivers are inverting level-shifters that accept EIA-232
input levels and translate them into 5 V logic output levels.
The inputs have internal 5 k
pull-down resistors to ground and
are also protected against overvoltages of up to
±
25 V. The
guaranteed switching thresholds are 0.8 V minimum and 2.8 V
maximum. An unconnected receiver input is pulled to 0 V by
the internal 5 k
pull-down resistor. This, therefore, results in a
Logic 1 output level for unconnected inputs or for inputs con-
nected to GND.
The receivers have Schmitt trigger input with a hysteresis level
of 0.25 V. This ensures error-free reception for both noisy in-
puts and for inputs with slow transition times.
SHUTDOWN INPUT
The shutdown input allows the ADM101E to be put into an
ultralow power mode where the dc-dc converter is switched off
and the transmitter is disabled. The receiver remains active
during shutdown. Logic 0 at this input enables the ADM101E,
while a Logic 1 at this input shuts down the ADM101E.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1020 | Circular Connector; No. of Contacts:26; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 |
| ADM1020AR-REEL | Circular Connector; No. of Contacts:26; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 |
| ADM1020AR-REEL7 | 8-Lead, Low-Cost, System Temperature Monitor |
| ADM1021A | Low-Cost Microprocessor System Temperature Monitor |
| ADM1021AARQ | Low-Cost Microprocessor System Temperature Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM101EARM-REEL | 功能描述:IC TXRX RS-232 SINGLE 5V 10MSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM101EARM-REEL7 | 功能描述:IC TXRX RS-232 SINGLE 5V 10MSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM101EARMZ | 功能描述:IC TX/RX RS-232 SINGLE 5V 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM101EARMZ | 制造商:Analog Devices 功能描述:RS-232 IC |
| ADM101EARMZ-REEL | 功能描述:IC TXRX RS-232 SINGLE 5V 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。