- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1024 (Analog Devices, Inc.) System Hardware Monitor with Remote Diode Thermal Sensing PDF資料下載
參數資料
| 型號： | ADM1024 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | System Hardware Monitor with Remote Diode Thermal Sensing |
| 中文描述： | 系統硬件監控與遠程二極管溫度傳感器 |
| 文件頁數： | 5/28頁 |
| 文件大小： | 285K |
| 代理商： | ADM1024 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADM1024
–5–
REV. 0
PIN FUNCTION DESCRIPTIONS
Pin
No.
Mnemonic
Description
1
NTEST_OUT/ADD
Digital I/O. Dual Function pin. This is a three-state input that controls the 2 LSBs of the Serial
Bus Address. This pin functions as an output when doing a NAND test.
Digital I/O. Dual Function pin. This pin functions as an interrupt output for temperature interrupts
only, or as an interrupt input for fan control. It has an on-chip 100 k
pull-up resistor.
Digital I/O. Serial Bus bidirectional Data. Open-drain output.
Digital Input. Serial Bus Clock.
Programmable Analog/Digital Input. 0 V to 2.5 V analog input or digital (0 to V
CC
) amplitude fan
tachometer input.
Programmable Analog/Digital Input. 0 V to 2.5 V analog input or digital (0 to V
CC
) amplitude fan
tachometer input.
Digital I/O. An active high input from an external latch which captures a Chassis Intrusion event.
This line can go high without any clamping action, regardless of the powered state of the ADM1024. The
ADM1024 provides an internal open drain on this line, controlled by Bit 6 of Register 40h or Bit 7 of
Register 46h, to provide a minimum 20 ms pulse on this line, to reset the external Chassis Intrusion Latch.
System Ground.
POWER (2.8 V to 5.5 V). Typically powered from 3.3 V power rail. Bypass with the parallel combination of
10
μ
F (electrolytic or tantalum) and 0.1
μ
F (ceramic) bypass capacitors.
Digital Output. Interrupt Request (open-drain). The output is enabled when Bit 1 of Register 40h
is set to 1. The default state is disabled. It has an on-chip 100 k
pull-up resistor.
Digital Input/Analog Output. An active-high input that enables NAND Test mode board-level connectivity
testing. Refer to section on NAND testing. Also functions as a programmable analog output when NAND
Test is not selected.
Digital I/O. Master Reset, 5 mA driver (open drain), active low output with a 45 ms minimum pulsewidth.
Set using Bit 4 in Register 40h. Also acts as reset input when pulled low (e.g., power-on reset). It has an
on-chip 100 k
pull-up resistor.
Analog Input. Connected to cathode of first external temperature sensing diode.
Analog Input. Connected to anode of first external temperature sensing diode.
Programmable Analog Input. Monitors 12 V supply.
Analog Input. Monitors 5 V supply.
Programmable Analog Input. Monitors second processor core voltage or cathode of second external
temperature sensing diode.
Programmable Analog Input. Monitors 2.5 V supply or anode of second external temperature sensing diode.
Analog Input. Monitors 1st processor core voltage (0 V to 3.6 V).
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID4 Status Regis-
ter. Can also be reconfigured as an interrupt input. It has an on-chip 100 k
pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 k
pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0-VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 k
pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 k
pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 k
pull-up resistor.
2
THERM
3
4
5
SDA
SCL
FAN1/AIN1
6
FAN2/AIN2
7
CI
8
9
GND
V
CC
10
INT
11
NTEST_IN/AOUT
12
RESET
13
14
15
16
17
D1–
D1+
+12 V
IN
+5 V
IN
V
CCP2
/D2–
18
19
20
+2.5 V
IN
/D2+
+V
CCP1
VID4/IRQ4
21
VID3/IRQ3
22
VID2/IRQ2
23
VID1/IRQ1
24
VID0/IRQ0
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1024ARU | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025 | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025A | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025AARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1025ARQ | Low-Cost PC Hardware Monitor ASIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARU | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024ARU-REEL | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024ARUZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1024ARUZ-R7 | 功能描述:板上安裝溫度傳感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。