欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1026JSTZ-REEL
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: Complete Thermal and System Management Controller
中文描述: 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
封裝: 7 X 7 MM, 1.40 MM HEIGHT, LEAD FREE, PLASTIC, MS-026BBC, LQFP-48
文件頁數: 14/56頁
文件大小: 634K
代理商: ADM1026JSTZ-REEL
ADM1026
Bit 3 of EEPROM Register 3 is used for EEPROM write protec-
tion. Setting this bit prevents accidental programming or era-
sure of the EEPROM. If an EEPROM write or erase operation
is attempted when this bit is set, the ADM1026 responds with
No Acknowledge. This bit is write-once and can only be cleared
by a power-on reset.
Rev. A | Page 14 of 56
EEPROM Register 3 Bit 7 is used for clock extend. Program-
ming an EEPROM byte takes approximately 250 μs, which
would limit the SMBus clock for repeated or block write opera-
tions. Because EEPROM block read/write access is slow, it is
recommended that this clock extend bit typically be set to 1.
This allows the ADM1026 to pull SCL low and extend the
clock pulse when it cannot accept any more data.
ADM1026 SMBus Operations
The SMBus specification defines several protocols for different
types of read and write operations. The ones used in the
ADM1026 are discussed below. The following abbreviations are
used in the diagrams:
S
W
P
A
R
A
ADM1026 Write Operations
Send Byte
In this operation, the master device sends a single command
byte to a slave device, as follows:
1.
The master device asserts a start condition on the SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts an ACK on the SDA.
4.
The master sends a command code.
5.
The slave asserts ACK on the SDA.
6.
The master asserts a stop condition on the SDA and the
transaction ends.
In the ADM1026, the send byte protocol is used to write a
register address to RAM for a subsequent single-byte read from
the same address or block read or write starting at that address.
This is illustrated in Figure 19.
Start
Write
Stop
Acknowledge
Read
No Acknowledge
S
ASLAVE
RAM
ADDRESS
(00h TO 6Fh)
A
A
P
1
2
3
4
5
6
0
Figure 19. Setting a RAM Address for Subsequent Read
If it is required to read data from the RAM immediately after
setting up the address, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single byte read, block read, or block write operation without
asserting an intermediate stop condition.
Write Byte/Word
In this operation, the master device sends a command byte and
one or two data bytes to the slave device as follows:
1.
The master device asserts a start condition on the SDA.
2.
The master sends the 7-bit slave address followed by the
write bit (low).
3.
The addressed slave device asserts an ACK on the SDA.
4.
The master sends a command code.
5.
The slave asserts an ACK on the SDA.
6.
The master sends a data byte.
7.
The slave asserts an ACK on the SDA.
8.
The master sends a data byte (or may assert stop here.)
9.
The slave asserts an ACK on the SDA.
10.
The master asserts a stop condition on the SDA to end the
transaction.
In the ADM1026, the write byte/word protocol is used for four
purposes. The ADM1026 knows how to respond by the value of
the command byte and EEPROM Register 3.
The first purpose is to write a single byte of data to RAM. In
this case, the command byte is the RAM address from 00h to
6Fh and the (only) data byte is the actual data. This is illustrated
in Figure 20.
S
ASLAVE
RAM
ADDRESS
(00h TO 6Fh)
1
2
3
4
5
6
A DATA A P
7
8
0
Figure 20. Single Byte Write to RAM
The protocol is also used to set up a 2-byte EEPROM address
for a subsequent read or block read. In this case, the command
byte is the high byte of the EEPROM address from 80h to 9Fh.
The (only) data byte is the low byte of the EEPROM address.
This is illustrated in Figure 21.
S
ASLAVE
EEPROM
ADDRESS
HIGH BYTE
(80h TO 9Fh)
1
3
4
5
6
A
A
7
A
2
P
8
EEPROM
ADDRESS
LOW BYTE
(00h TO FFh)
0
Figure 21. Setting an EEPROM Address
If it is required to read data from the EEPROM immediately
after setting up the address, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single-byte read or block read operation without asserting an
intermediate stop condition. In this case, Bit 0 of EEPROM
Register 3 should be set.
The third use is to erase a page of EEPROM memory. EEPROM
memory can be written to only if it is previously erased. Before
writing to one or more EEPROM memory locations that are
already programmed, the page or pages containing those
locations must first be erased. EEPROM memory is erased by
writing an EEPROM page address plus an arbitrary byte of data
with Bit 2 of EEPROM Register 3 set to 1.
相關PDF資料
PDF描述
ADM1026JST Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28
ADM1030ARQ Intelligent Temperature Monitor and PWM Fan Controller
ADM1030 Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35
ADM1033 Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQ Thermal Monitor and Fan Speed (RPM) Controller
相關代理商/技術參數
參數描述
ADM1026JSTZ-REEL7 制造商:Analog Devices 功能描述:IC SYSTEM MONITOR 制造商:ON Semiconductor 功能描述:IC SYSTEM MONITOR
ADM1027 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCOOL-TM Remote Thermal Controller and Voltage Monitor
ADM1027ARQ 功能描述:IC THER CTRL VOLT/MONITOR 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓?fù)?ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1027ARQ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓?fù)?ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1027ARQ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓?fù)?ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
主站蜘蛛池模板: 高要市| 措勤县| 大城县| 晋城| 延庆县| 和硕县| 沧源| 陆丰市| 广昌县| 鲜城| 什邡市| 娄底市| 太谷县| 沅陵县| 新源县| 错那县| 敦化市| 平遥县| 松阳县| 桐柏县| 遂宁市| 苗栗县| 高雄市| 开鲁县| 浠水县| 南陵县| 汾西县| 互助| 伊宁市| 江津市| 虞城县| 突泉县| 临夏县| 富阳市| 且末县| 景德镇市| 鄂伦春自治旗| 桂阳县| 邯郸市| 洛宁县| 谢通门县|