- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1030ARQ (ANALOG DEVICES INC) Intelligent Temperature Monitor and PWM Fan Controller PDF資料下載
參數資料
| 型號： | ADM1030ARQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Intelligent Temperature Monitor and PWM Fan Controller |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 1Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MO-137AB, QSOP-16 |
| 文件頁數： | 16/28頁 |
| 文件大小： | 278K |
| 代理商： | ADM1030ARQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. 0
ADM1030
–16–
FILTERED CONTROL MODE
The Automatic Fan Speed Control Loop reacts instantaneously
to changes in temperature, i.e., the PWM duty cycle will respond
immediately to temperature change. In certain circumstances,
we may not want the PWM output to react instantaneously to
temperature changes. If significant variations in temperature
were found in a system, it would have the effect of changing the
fan speed, which could be obvious to someone in close proxim-
ity. One way to improve the system’s acoustics would be to
slow down the loop so that the fan ramps slowly to its newly
calculated fan speed. This also ensures that temperature transients
will effectively be ignored, and the fan’s operation will be smooth.
There are two means by which to apply filtering to the Auto-
matic Fan Speed Control Loop. The first method is to ramp the
fan speed at a predetermined rate, to its newly calculated value
instead of jumping directly to the new fan speed. The second
approach involves changing the on-chip ADC sample rate, to
change the number of temperature readings taken per second.
The filtered mode on the ADM1030 is invoked by setting Bit 0
of the Fan Filter Register (Register 0x23). Once the Fan Filter
Register has been written to, and all other control loop param-
eters (T
MIN
, T
RANGE
, etc.) have been programmed, the device
may be placed into Automatic Fan Speed Control Mode by
setting Bit 7 of Configuration Register 1 (Register 0x00) to 1.
Effect of Ramp Rate on Filtered Mode
Bits <6:5> of the Fan Filter Register determine the ramp rate in
Filtered Mode. The PWM_OUT signal driving the fan will have
a period, T, given by the PWM_OUT drive frequency, f, since
T = 1/f. For a given PWM period, T, the PWM period is subdi-
vided into 240 equal time slots. One time slot corresponds to
the smallest possible increment in PWM duty cycle. A PWM
signal of 33% duty cycle will thus be high for 1/3
×
240 time
slots and low for 2/3
×
240 time slots. Therefore, 33% PWM
duty cycle corresponds to a signal which is high for 80 time slots
and low for 160 time slots.
PWM_OUT
33% DUTY
CYCLE
160 TIME
SLOTS
80 TIME
SLOTS
PWM OUTPUT
(ONE PERIOD) =
240 TIME SLOTS
Figure 11. 33% PWM Duty Cycle Represented in Time
Slots
The ramp rates in Filtered Mode are selectable between 1, 2, 4,
and 8. The ramp rates are actually discrete time slots. For
example, if the ramp rate = 8, then eight time slots will be added
to the PWM_OUT high duty cycle each time the PWM_OUT
duty cycle needs to be increased. Figure 12 shows how the
Filtered Mode algorithm operates.
INCREMENT
PREVIOUS PWM
VALUE BY RAMP
RATE
READ
TEMPERATURE
CALCULATE
NEW PWM
DUTY CYCLE
IS NEW
PWM VALUE >
PREVIOUS
VALUE
DECREMENT
PREVIOUS
PWM VALUE
BY RAMP
RATE
YES
NO
Figure 12. Filtered Mode Algorithm
The Filtered Mode algorithm calculates a new PWM duty cycle
based on the temperature measured. If the new PWM duty cycle
value is greater than the previous PWM value, the previous PWM
duty cycle value is incremented by either 1, 2, 4, or 8 time slots
(depending on the setting of bits <6:5> of the Fan Filter Regis-
ter). If the new PWM duty cycle value is less than the previous
PWM value, the previous PWM duty cycle is decremented by 1,
2, 4, or 8 time slots. Each time the PWM duty cycle is incremented
or decremented, it is stored as the previous PWM duty cycle for
the next comparison.
So what does an increase of 1, 2, 4, or 8 time slots actually mean
in terms of PWM duty cycle
A Ramp Rate of 1 corresponds to one time slot, which is 1/240
of the PWM period. In Filtered Auto Fan Speed Control Mode,
incrementing or decrementing by 1 changes the PWM output
duty cycle by 0.416%.
Table VIII. Effect of Ramp Rates on PWM_OUT
Ramp Rate
PWM Duty Cycle Change
1
2
4
8
0.416%
0.833%
1.66%
3.33%
So programming a ramp rate of 1, 2, 4, or 8 simply increases
or decreases the PWM duty cycle by the amounts shown in
Table V, depending on whether the temperature is increasing
or decreasing.
Figure 13 shows remote temperature plotted against PWM duty
cycle for Filtered Mode. The ADC sample rate is the highest
sample rate; 11.25 kHz. The ramp rate is set to 8 which would
correspond to the fastest ramp rate. With these settings it took
approximately 12 seconds to go from 0% duty cycle to 100%
duty cycle (full-speed). The T
MIN
value = 32
°
C and the T
RANGE
= 80
°
C. It can be seen that even though the temperature increased
very rapidly, the fan gradually ramps up to full speed.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
| ADM1033 | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL | Thermal Monitor and Fan Speed (RPM) Controller |
| ADM1033ARQ-REEL7 | Thermal Monitor and Fan Speed (RPM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1030ARQ-REEL | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQ-REEL7 | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1030ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1030ARQZ-REEL | 功能描述:板上安裝溫度傳感器 TDM PWM FAN CTRLRS IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1030ARQZ-REEL7 | 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。