欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1033ARQ-REEL
廠商: ANALOG DEVICES INC
元件分類: 溫度/濕度傳感器
英文描述: Thermal Monitor and Fan Speed (RPM) Controller
中文描述: DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT
封裝: MO-137AB, QSOP-16
文件頁數: 14/40頁
文件大小: 1164K
代理商: ADM1033ARQ-REEL
ADM1033
REGISTER ADDRESSES FOR
SINGLE/BLOCK BYTE MODES
The ADM1033 supports single-byte and multiple-byte (block)
read and write operations. The register address determines
whether a single-byte or block operation is run. For a single-
byte operation, the MSB of the register address is set to 0; for a
multiple-byte operation, it is set to 1. The number of bytes read
from the ADM1033 in a multiple-byte operation is set in the
#Bytes/Block Read Register at Address 0x00. The number of
bytes written to it is specified in the block-write operation. The
addresses quoted in the register map and throughout this data
sheet assume single-byte operation. For multiple-byte opera-
tions, set the MSB of each register address to 1.
Rev. 0 | Page 14 of 40
The SMBus specifications define protocols for different types of
read and write operations. The ADM1033 supports the
following SMBus write protocols: send byte, write byte, block
write, receive byte, and block read. The following abbreviations
are used in the diagrams:
S—START
P—STOP
R—READ
W—WRITE
A—ACKNOWLEDGE
A—NO ACKNOWLEDGE
WRITE OPERATIONS
Send Byte
In this operation, the master device sends a single-command
byte to a slave device as follows:
1.
The master device asserts a start condition on SDA.
2.
The master sends a 7-bit address followed by the write bit
(low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends the register address.
5.
The slave asserts ACK on SDA.
6.
The master asserts a stop condition on SDA, and the
transaction ends.
SLAVE
ADDRESS
S
REG
ADDRESS
W A
A P
0
Figure 21. Send Byte
The ADM1033 uses the send-byte operation to write a register
address to the APR for a subsequent read from the same
address. This is illustrated in Figure 21. The user may be
required to read data from the register immediately after setting
up the address. If so, the master can assert a repeat start
condition immediately after the final ACK and carry out a
single-byte read without asserting an intermediate stop condition.
Write Byte
In this operation, the master device sends the register address
and one data byte to the slave device as follows:
1.
2.
The master asserts a start condition on SDA.
The master sends the 7-bit slave address followed by a
write bit (low).
The addressed slave device asserts ACK on SDA.
The master sends the register address. The MSB of the
command code should equal 0 for a write-byte operation.
If the MSB equals 1, a block-write operation takes place.
The slave asserts ACK on SDA.
The master sends a data byte.
The slave asserts ACK on SDA.
The master asserts a stop condition on SDA to end the
transaction.
3.
4.
5.
6.
7.
8.
SLAVE
ADDRESS
S
REG
ADDRESS
DATA
W
A
A
A
P
0
Figure 22. Write Byte
Block Write
In this operation, the master device writes a block of data to a
slave address as follows. A maximum number of 32 bytes can
be written.
1.
The master asserts a start condition on SDA.
2.
The master sends the 7-bit slave address followed by a write
bit (low).
3.
The addressed slave device asserts ACK on SDA.
4.
The master sends the register address. This register address
sets up the address pointer register and determines if a
block write (MSB = 1) or a byte write (MSB = 0) takes place.
5.
The slave asserts ACK on SDA.
6.
The master sends the byte count.
7.
The slave asserts ACK on SDA.
8.
The master sends N data bytes.
9.
The slave asserts ACK on SDA after each byte.
10.
The master asserts a stop condition on SDA to end the
transaction.
SLAVE
ADDRESS
S
BYTE
COUNT
DATA 2
DATA 1
REGISTER
ADDRESS
W
A
A
P
A
A
A
DATA N
A
0
Figure 23. Block Write
相關PDF資料
PDF描述
ADM1033ARQ-REEL7 Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQZ Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQZ-REEL Thermal Monitor and Fan Speed (RPM) Controller
ADM1033ARQZ-REEL7 Thermal Monitor and Fan Speed (RPM) Controller
ADM1041ARQ-REEL Secondary-Side Controller with Current Share and Housekeeping
相關代理商/技術參數
參數描述
ADM1033ARQ-REEL7 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1033ARQZ 功能描述:馬達/運動/點火控制器和驅動器 +/- 1 C Digital 2-Wire RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1033ARQZ-REEL 功能描述:板上安裝溫度傳感器 +/- 1 C Digital 2-Wire RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADM1033ARQZ-REEL7 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1033ARQZ-RL7 功能描述:IC THERM/FAN SPEED CTLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
主站蜘蛛池模板: 泉州市| 遵义县| 黔西| 北川| 股票| 乌拉特后旗| 扎赉特旗| 徐水县| 武邑县| 三穗县| 张家界市| 赣榆县| 屏东市| 都江堰市| 武冈市| 汉沽区| 岳阳市| 揭东县| 和田市| 通河县| 泰安市| 自治县| 广灵县| 翼城县| 定兴县| 拜城县| 临西县| 芷江| 高邑县| 天祝| 柯坪县| 丘北县| 平塘县| 南昌县| 东乌珠穆沁旗| 牡丹江市| 柳林县| 邛崃市| 灵石县| 阳谷县| 宜州市|