- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1041 (Analog Devices, Inc.) Secondary-Side Controller with Current Share and Housekeeping PDF資料下載
參數資料
| 型號： | ADM1041 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Secondary-Side Controller with Current Share and Housekeeping |
| 中文描述： | 二次側電流控制器共享和管家 |
| 文件頁數： | 33/64頁 |
| 文件大小： | 1063K |
| 代理商： | ADM1041 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
ADM1041
SMBus SERIAL PORT
The programming and microprocessor interface for the
ADM1041 is a standard SMBus serial port, which consists of a
clock line and a data line. The more rigorous requirements of
the SMBus standard are specified in order to give the greatest
noise immunity. The ADM1041 operates in slave mode only. If a
microprocessor is not used, these pins can be configured to
perform the PS
ON
LINK and AC_OKLink functions. Note that
this port is not intended to be connected to the customer’s
SMBus (or I
2
C bus). Continuous SMBus activity or an external
bus fault interferes with the inter-ASIC communication, possibly
preventing proper operation and proper fault reporting. If the
customer needs status and control functions via the SMBus, it is
recommended that a microprocessor with a hardware SMBus
(I
2
C) port be used for this interface. The microprocessor should
access the ASICs via a second SMBus port, which may be emu-
lated in software (subset of the full protocol).
SDA/PS
ON
LINK
The SDA pin normally carries data in and out of the ASIC
during programming/configuration or while reading/writing by
a microprocessor. If a microprocessor is not used, this pin can
be configured as PS
ON
LINK and can be connected to the same
pin on other ADM1041s in the power supply. If a fault is
detected in any ADM1041, causing it to shut down, it uses this
pin to signal the other ADM1041s to also shut down. If an auto-
restart has been configured, it also causes all ADM1041s to turn
on together.
SCL/AC_OKLink
The SCL pin normally provides a clock signal into the ASIC
during programming/configuration or while reading/writing by
a microprocessor. If a microprocessor is not used, this pin can
be configured as AC_OKLink, and can be connected to the
same pin on other ADM1041s in the power supply. This allows
a single ADM1041 to be used for ac sensing and helps to
synchronize the start-up of multiple ADM1041s.
ADD0
This pin configures two bits of the chip address for the SMBus.
It is three-level and can be pulled high to V
DD
, pulled low to
ground, or left floating (internally biased to 2.5 V). An additional
bit may be set during configuration, which allows up to six
ADM1041s to be used in a single power supply. The state of
ADD0 is continuously sampled after V
DD
power-up. After the
first time the ADM1041 is successfully addressed, the internal
bias is released and ADD0 becomes high impedance.
Rev. A | Page 33 of 64
MICROPROCESSOR SUPPORT
The ADM1041 has many features that allow it to operate with
the aid of a microprocessor. There are several reasons why a
microprocessor might be used:
To provide unusual logic and/or timing requirements,
particularly for fault conditions.
To drive one or more LEDs, including flashing, according
to the status of the power supply.
To replace other discrete circuits such as multiple OTP,
extra output monitoring, fan speed control, and failure
detection, and combine the status of these circuits with the
status of the ADM1041s.
To free up some pins on the ADM1041s. This could reduce
the number of ASICs and therefore the cost.
To interface to an external SMBus (or I
2
C) for more
detailed status reporting. The SMBus port in the ADM1041
is not intended for this purpose.
To allow EEPROM space in ADM1041(s) or in the
microprocessor to be used for FRU (VPD) data. A simple
or complex microprocessor can be used according to the
amount of additional functionality required. Note that the
microprocessor is not intended to access or modify the
EEPROM address space that is used for the configuration
of the ADM1041(s).
Interfacing
The microprocessor must access the ADM1041(s) via their
on-board SMBus (I
2
C) port. Since this port is also used for
configuration of the ADM1041(s), the software must include a
routine that avoids SMBus activity during the configuration
process. The simplest interface is for the microprocessor to have
an SMBus (I
2
C) port implemented in hardware, but this may be
more expensive. An alternative is to emulate the bus in software
and to use two general-purpose logic I/O pins. Only a simple
subset of the SMBus protocol need be emulated because the
ADM1041 always operates as a slave device.
Configuring for a Microprocessor
Except during initial configuration, all ADM1041 registers that
need to be accessed are high speed CMOS devices that do not
involve EEPROM. The Microprocessor Support table (Table 43)
details the various registers, bits, and flags that can be read and
written to, including explanations.
Note that for the microprocessor to gain control of the PSON
and AC
SENSE
functions, the normal signal path in the ADM1041
must be configured to be broken. A separate configuration bit is
allocated to each signal. The microprocessor can then write to
the signal after the break as though the signal originated within
the ADM1041 itself. The original signals can still be read prior
to the break.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1041ARQ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL | Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ-REEL7 | Secondary-Side Controller with Current Share and Housekeeping |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1041A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041AARQZ-REEL7 | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ADM1041A-EVALZ | 功能描述:BOARD EVAL FOR ADM1041A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
發布緊急采購，3分鐘左右您將得到回復。