- 您現在的位置：買賣IC網 > PDF目錄373996 > ADM1064ASU-REEL (ANALOG DEVICES INC) Super Sequencer with Voltage Readback ADC PDF資料下載
參數資料
| 型號： | ADM1064ASU-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Super Sequencer with Voltage Readback ADC |
| 中文描述： | 10-CHANNEL POWER SUPPLY SUPPORT CKT, QFP48 |
| 封裝： | 7 X 7 MM, MS-026ABC, TQFP-48 |
| 文件頁數： | 17/32頁 |
| 文件大小： | 523K |
| 代理商： | ADM1064ASU-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADM1064
SEQUENCING ENGINE
OVERVIEW
The ADM1064’s sequencing engine (SE) provides the user with
powerful and flexible control of sequencing. The SE implements
a state machine control of the PDO outputs, with state changes
conditional on input events. SE programs can enable complex
control of boards such as power-up and power-down sequence
control, fault event handling, interrupt generation on warnings,
and so on. A watchdog function that verifies the continued
operation of a processor clock can be integrated into the SE
program. The SE can also be controlled via the SMBus, giving
software or firmware control of the board sequencing.
Rev. 0 | Page 17 of 32
The SE state machine comprises 63 state cells. Each state has the
following attributes:
Monitors signals indicating the status of the 10 input pins,
VP1 to VP4, VH, and VX1 to VX5.
Can be entered from any other state.
Three exit routes move the state machine on to a next state:
sequence detection, fault monitoring, and timeout.
Delay timers for the sequence and timeout blocks can be
programmed independently, and change with each state
change. The range of timeouts is from 0 ms to 400 ms.
Output condition of the 10 PDO pins is defined and fixed
within a state.
Transition from one state to the next is made in less than
20 μs, which is the time needed to download a state definition
from EEPROM to the SE.
0
SEQUENCE
TIMEOUT
MOFAULT
STATE
Figure 23. State Cell
The ADM1064 offers up to 63 state definitions. The signals
monitored to indicate the status of the input pins are the
outputs of the SFDs.
WARNINGS
The SE also monitors warnings. These warnings can be
generated when the ADC readings violate their limit register
value or when the secondary voltage monitors on VP1–4 and
VH. The warnings are all OR’ed together and are available as a
single warning input to each of the three blocks that enable
exiting from a state.
SMBUS JUMP/UNCONDITIONAL JUMP
The SE can be forced to advance to the next state uncondition-
ally. This enables the user to force the SE to advance. Examples
of where this might be used include moving to a margining
state or debugging a sequence. The SMBus jump or go-to
command can be seen as another input to sequence and
timeout blocks, which provide an exit from each state.
Table 6. Sample Sequence State Entries
State
Sequence
IDLE1
If VX1 is low , go to state IDLE2.
IDLE2
If VP1 is okay, go to state EN3V3.
EN3V3
If VP2 is okay, go to state EN2V5.
Timeout
If VP2 is not okay after 10 ms, go to
state DIS3V3.
If VP3 is not okay after 20 ms, go to
state DIS2V5.
Monitor
If VP1 is not okay, go to state IDLE1.
DIS3V3
EN2V5
If VX1 is high, go to state IDLE1.
If VP3 is okay, go to state PWRGD.
If VP1 or VP2 is not okay, go to state FSEL2.
DIS2V5
FSEL1
FSEL2
PWRGD
If VX1 is high, go to state IDLE1.
If VP3 is not okay, go to state DIS2V5.
If VP2 is not okay, go to state DIS3V3.
If VX1 is high, go to state DIS2V5.
If VP1 or VP2 is not okay, go to state FSEL2.
If VP1 is not okay, go to state IDLE1.
If VP1, VP2, or VP3 is not okay, go to state
FSEL1.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1064ASU-REEL7 | Super Sequencer with Voltage Readback ADC |
| ADM1065 | Super Sequencer-TM and Monitor |
| ADM1065ACP | Super Sequencer-TM and Monitor |
| ADM1065ACP-REEL | Super Sequencer-TM and Monitor |
| ADM1065ACP-REEL7 | Super Sequencer-TM and Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1064ASU-REEL7 | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 48-Pin TQFP T/R |
| ADM1064ASUZ | 功能描述:IC SEQUENCER/SUPERVISOR 48-TQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V，2.955V，可調，可調，可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6 |
| ADM1065 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Super Sequencer-TM and Monitor |
| ADM1065ACP | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer/Monitor 2.7V to 5.4V 40-Pin LFCSP EP |
| ADM1065ACP-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Super Sequencer-TM and Monitor |
發布緊急采購，3分鐘左右您將得到回復。