- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM3485EAN (ANALOG DEVICES INC) ESD Protected, EMC Compliant, 3.3 V, 20 Mbps, EIA RS-485 Transceiver PDF資料下載
參數資料
| 型號： | ADM3485EAN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | ESD Protected, EMC Compliant, 3.3 V, 20 Mbps, EIA RS-485 Transceiver |
| 中文描述： | LINE TRANSCEIVER, PDIP8 |
| 封裝： | MO-095AA, PLASTIC, DIP-8 |
| 文件頁數： | 10/11頁 |
| 文件大小： | 119K |
| 代理商： | ADM3485EAN |
ADM3485E
–10–
REV. A
Test results are classified according to the following
1. Normal performance within specification limits.
2. Temporary degradation or loss of performance that is self-
recoverable.
3. Temporary degradation or loss of function or performance
that requires operator intervention or system reset.
4. Degradation or loss of function that is not recoverable due to
damage.
APPLICATIONS INFORMATION
Differential Data Transmission
Differential data transmission is used to reliably transmit data at
high rates over long distances and through noisy environments.
Differential transmission nullifies the effects of ground shifts
and noise signals that appear as common-mode voltages on the
line.
Two main standards are approved by the Electronics Industries
Association (EIA) which specify the electrical characteristics of
transceivers used in differential data transmission. The RS-422
standard specifies data rates up to 10 MBaud and line lengths
up to 4000 ft. A single driver can drive a transmission line with
up to 10 receivers.
The RS-485 standard was defined to cater to true multipoint
communications. This standard meets or exceeds all the re-
quirements of RS-422, but also allows multiple drivers and
receivers to be connected to a single bus. An extended common-
mode range of –7 V to +12 V is defined.
The most significant difference between RS-422 and RS-485 is
the fact that the drivers may be disabled thereby allowing more
than one to be connected to a single line. Only one driver should
be enabled at a time, but the RS-485 standard contains addi-
tional specifications to guarantee device safety in the event of
line contention.
Cable and Data Rate
The transmission line of choice for RS-485 communications is a
twisted pair. Twisted pair cable tends to cancel common-mode
noise and also causes cancellation of the magnetic fields gener-
ated by the current flowing through each wire, thereby reducing
the effective inductance of the pair.
The ADM3485E is designed for bidirectional data communica-
tions on multipoint transmission lines. A typical application
showing a multipoint transmission network is illustrated in
Figure 23. Only one driver can transmit at a particular time, but
multiple receivers may be enabled simultaneously.
As with any transmission line, it is important that reflections are
minimized. This may be achieved by terminating the extreme
ends of the line using resistors equal to the characteristic imped-
ance of the line. Stub lengths of the main line should also be
kept as short as possible. A properly terminated transmission
line appears purely resistive to the driver.
Receiver Open-Circuit Fail-Safe
The receiver input includes a fail-safe feature that guarantees a
logic high on the receiver when the inputs are open circuit or
floating.
Table VI. Comparison of RS-422 and RS-485 Interface
Standards
Specification
RS-422
RS-485
Transmission Type
Maximum Cable Length
Minimum Driver Output Voltage
±
2 V
Driver Load Impedance
Receiver Input Resistance
Receiver Input Sensitivity
Receiver Input Voltage Range
Differential
4000 ft.
Differential
4000 ft.
±
1.5 V
54
12 k
min
±
200 mV
100
4 k
min
±
200 mV
–7 V to +7 V –7 V to +12 V
相關PDF資料 |
PDF描述 |
|---|---|
| ADM3491ARU | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491 | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491AN | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491AR | MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:90V; Continuous Drain Current, Id:0.86A; On-Resistance, Rds(on):4ohm; Rds(on) Test Voltage, Vgs:10V; Package/Case:TO-205AD; Drain-Source Breakdown Voltage:90V RoHS Compliant: No |
| ADM483EAN | +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM3485EANZ | 制造商:Rochester Electronics LLC 功能描述:3 VOLT RS-485 HIGH ESD I.C. - Bulk 制造商:Analog Devices 功能描述:TRANSCEIVER RS485/422 3.3V 3485 |
| ADM3485EAR | 功能描述:IC TX/RX RS-485 HS 3.3V 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| ADM3485EAR-REEL | 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:3 VOLT RS-485 HIGH ESD I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC TRANSCEIVER RS485 |
| ADM3485EAR-REEL7 | 功能描述:IC TXRX RS-485 HS 3.3V 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM3485EARZ | 功能描述:IC TX/RX RS-485 HS 3.3V 8-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
發布緊急采購，3分鐘左右您將得到回復。