- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM3485EAR (ANALOG DEVICES INC) ESD Protected, EMC Compliant, 3.3 V, 20 Mbps, EIA RS-485 Transceiver PDF資料下載
參數資料
| 型號： | ADM3485EAR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | ESD Protected, EMC Compliant, 3.3 V, 20 Mbps, EIA RS-485 Transceiver |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封裝： | MS-012AA, SOIC-8 |
| 文件頁數： | 8/11頁 |
| 文件大小： | 119K |
| 代理商： | ADM3485EAR |
ADM3485E
–8–
REV. A
Table I. Comparison of RS-422 and RS-485 Interface Standards
Specification
RS-422
RS-485
Transmission Type
Maximum Data Rate
Maximum Cable Length
Minimum Driver Output Voltage
Driver Load Impedance
Receiver Input Resistance
Receiver Input Sensitivity
Receiver Input Voltage Range
No. of Drivers/Receivers Per Line
Differential
10 MB/s
4000 ft.
±
2 V
100
4 k
min
±
200 mV
–7 V to +7 V –7 V to +12 V
1/10
Differential
10 MB/s
4000 ft.
±
1.5 V
54
12 k
min
±
200 mV
32/32
Table II. Transmitting Truth Table
Transmitting
Inputs
Outputs
RE
DE
DI
B
A
X
X
0
1
1
1
0
0
1
0
X
X
0
1
Hi-Z
Hi-Z
1
0
Hi-Z
Hi-Z
Table III. Receiving Truth Table
Receiving
Inputs
DE
Outputs
RO
RE
A–B
0
0
0
1
X
X
X
X
> +0.2 V
< –0.2 V
Inputs O/C
X
1
0
1
Hi-Z
ESD/EFT TRANSIENT PROTECTION SCHEME
The ADM3485E uses protective clamping structures on its
inputs and outputs that clamp the voltage to a safe level and
dissipate the energy present in ESD (Electrostatic) and EFT
(Electrical Fast Transients) discharges.
The protection structure achieves ESD protection up to
±
8 kV
according to IEC1000-4-2, and EFT protection up to
±
2 kV on
all I-O lines.
ESD TESTING
Two coupling methods are used for ESD testing, contact dis-
charge and air-gap discharge. Contact discharge calls for a di-
rect connection to the unit being tested. Air-gap discharge uses
a higher test voltage but does not make direct contact with the
unit under test. With air discharge, the discharge gun is moved
toward the unit under test, developing an arc across the air gap,
hence the term air-discharge. This method is influenced by hu-
midity, temperature, barometric pressure, distance and rate of
closure of the discharge gun. The contact-discharge method,
while less realistic, is more repeatable and is gaining acceptance
and preference over the air-gap method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time, coupled with high voltages, can
cause failures in unprotected semiconductors. Catastrophic
destruction can occur immediately as a result of arcing or heat-
ing. Even if catastrophic failure does not occur immediately, the
device may suffer from parametric degradation, which may
result in degraded performance. The cumulative effects of con-
tinuous exposure can eventually lead to complete failure.
I-O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I-O cable can result in a static dis-
charge that can damage or completely destroy the interface
product connected to the I-O port.
It is extremely important, therefore, to have high levels of ESD
protection on the I-O lines.
It is possible that the ESD discharge could induce latchup in the
device under test, so it is important that ESD testing on the I-O
pins be carried out while device power is applied. This type of
testing is more representative of a real-world I-O discharge
where the equipment is operating normally when the discharge
occurs.
TEMPERATURE
–
C
1.20
–
50
70
–
30
I
C
–
–
10
10
30
50
1.15
1.05
1.00
0.95
0.80
1.10
0.90
0.85
90
110
0.75
0.70
I
CC
(mA)
RE
= LO, DE = LO
I
CC
(mA) DE = V
CC
,
RE
= X
Figure 19. Supply Current vs. Temperature
TEMPERATURE
–
C
100
–
40
80
–
20
I
C
–
0
20
40
60
90
70
60
50
20
80
40
30
10
0
I
CC
(mA)
Figure 20. Shutdown Current vs. Temperature
相關PDF資料 |
PDF描述 |
|---|---|
| ADM3485EAN | ESD Protected, EMC Compliant, 3.3 V, 20 Mbps, EIA RS-485 Transceiver |
| ADM3491ARU | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491 | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491AN | 3.3 V, Full Duplex, 840 uA 20 Mbps, EIA RS-485 Transceiver |
| ADM3491AR | MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:90V; Continuous Drain Current, Id:0.86A; On-Resistance, Rds(on):4ohm; Rds(on) Test Voltage, Vgs:10V; Package/Case:TO-205AD; Drain-Source Breakdown Voltage:90V RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM3485EAR-REEL | 制造商:Analog Devices 功能描述:Single Transmitter/Receiver RS-422/RS-485 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:3 VOLT RS-485 HIGH ESD I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC TRANSCEIVER RS485 |
| ADM3485EAR-REEL7 | 功能描述:IC TXRX RS-485 HS 3.3V 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM3485EARZ | 功能描述:IC TX/RX RS-485 HS 3.3V 8-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM3485EARZ | 制造商:Analog Devices 功能描述:3 VOLT RS-485 HIGH ESD I.C. |
| ADM3485EARZ-REEL | 功能描述:IC TXRX RS-485 3.3V 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。