- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM483EAR (ANALOG DEVICES INC) +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver PDF資料下載
參數資料
| 型號： | ADM483EAR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 324K |
| 代理商： | ADM483EAR |
–6–
REV. 0
ADM483E
GENERAL INFORMATION
The ADM483E is a ruggedized RS-485 transceiver that operates
from a single +5 V supply.
It contains protection against radiated and conducted interfer-
ence, including high levels of electrostatic discharge.
It is ideally suited for operation in electrically harsh environ-
ments or where cables may be plugged/unplugged. It is also
immune to high RF field strengths without special shielding
precautions. It is intended for balanced data transmission and
complies with both EIA Standards RS-485 and RS-422. It con-
tains a differential line driver and a differential line receiver, and
is suitable for half duplex data transmission as the driver and
receiver share the same differential pins.
The input impedance on the ADM483E is 12 k
, allowing up to
32 transceivers on the differential bus.
The ADM483E operates from a single +5 V
±
10% power
supply. Excessive power dissipation caused by bus contention or
by output shorting is prevented by a thermal shutdown circuit.
This feature forces the driver output into a high impedance state
if, during fault conditions, a significant temperature increase is
detected in the internal driver circuitry.
The receiver contains a fail-safe feature that results in a logic
high output state if the inputs are unconnected (floating).
A high level of robustness is achieved using internal protection
circuitry, eliminating the need for external protection compo-
nents such as tranzorbs or surge suppressors.
Low electromagnetic emissions are achieved using slew limited
drivers, minimizing interference both conducted and radiated.
The ADM483 can transmit at data rates up to 250 kbps.
A typical application for the ADM483E is illustrated in Figure
20. This shows a half-duplex link where data may be transferred
at rates up to 250 kbps. A terminating resistor is shown at both
ends of the link. This termination is not critical since the slew
rate is controlled by the ADM483E and reflections are minimized.
The communications network may be extended to include
multipoint connections as shown in Figure 30. Up to 32
transceivers may be connected to the bus.
ADM483E
ADM483E
RS485/RS-422 LINK
+5V
+5V
0.1μF
0.1μF
V
CC
V
CC
RE
RO
DI
DE
DI
DE
B
A
GND
B
A
GND
RE
RO
Figure 20. Typical Half-Duplex Link Application
Tables II and III show the truth tables for transmitting and
receiving.
Table II. Transmitting Truth Table
Inputs
Outputs
B
0
1
Hi-Z
Hi-Z
RE
X
X
0
1
DE
1
1
0
0
DI
1
0
X
X
A
1
0
Hi-Z
Hi-Z
X = Don’t Care.
Table III. Receiving Truth Table
Inputs
RE
0
0
0
1
Outputs
DE
0
0
0
0
A-B
≥
+0.2 V
≤
–0.2 V
Inputs O/C
X
RO
1
0
1
Hi-Z
X = Don’t Care.
ESD/EFT TRANSIENT PROTECTION SCHEME
The ADM483E uses protective clamping structures on its
inputs and outputs that clamp the voltage to a safe level and
dissipates the energy present in ESD (Electrostatic) and EFT
(Electrical Fast Transients) discharges.
The protection structure achieves ESD protection up to
±
15 kV
according to the Human Body Model, and EFT protection up
to
±
2 kV on all I-O lines.
ESD TESTING
Two coupling methods are used for ESD testing, contact
discharge and air-gap discharge. Contact discharge calls for a
direct connection to the unit being tested. Air-gap discharge
uses a higher test voltage but does not make direct contact with
the unit under test. With air discharge, the discharge gun is
moved toward the unit under test, developing an arc across the
air gap, hence the term air-discharge. This method is influenced
by humidity, temperature, barometric pressure, distance and
rate of closure of the discharge gun. The contact-discharge
method, while less realistic, is more repeatable and is gaining
acceptance and preference over the air-gap method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time, coupled with high voltages, can
cause failures in unprotected semiconductors. Catastrophic
destruction can occur immediately as a result of arcing or
heating. Even if catastrophic failure does not occur immedi-
ately, the device may suffer from parametric degradation, which
may result in degraded performance. The cumulative effects of
continuous exposure can eventually lead to complete failure.
HIGH
VOLTAGE
GENERATOR
DEVICE
UNDER TEST
ESD Test Method
Human Body Model
R2
1.5K
C1
100pF
C1
R2
Figure 21. ESD Generator
相關PDF資料 |
PDF描述 |
|---|---|
| ADM483E | +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
| ADM483 | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL7 | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM483EAR-1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM483EAR-1REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM483EAR-REEL | 功能描述:IC TX/RX RS-485 LO-SLEW 5V 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM483EARZ | 功能描述:IC TX/RX RS-485 LO-SLEW 5V 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| ADM483EARZ | 制造商:Analog Devices 功能描述:Transceiver IC 制造商:Analog Devices 功能描述:IC, RS485 TRANSCEIVER 250KBPS 5.5V SOIC8 |
發布緊急采購，3分鐘左右您將得到回復。