- 您現在的位置：買賣IC網 > PDF目錄374009 > ADM708R (Analog Devices, Inc.) +3 V, Voltage Monitoring uP Supervisory Circuits PDF資料下載
參數資料
| 型號： | ADM708R |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | +3 V, Voltage Monitoring uP Supervisory Circuits |
| 中文描述： | 3伏，電壓的監察監控電路 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 129K |
| 代理商： | ADM708R |
REV. A
–5–
ADM706P/R/S/T, ADM708R/S/T
WATCHDOG
TRANSITION
DETECTOR
WATCHDOG
TIMER
1.25V
V
REF
*
WATCHDOG
INPUT (WDI)
POWER FAIL
INPUT (PFI)
POWER FAIL
OUTPUT (
PFO
)
WATCHDOG
OUTPUT(
WDO
)
RESET
,
(P = RESET)
*
VOLTAGE REFERENCE = 2.63V (P/R), 2.93V (S), 3.08V (T)
ADM706
RESET &
WATCHDOG
TIMEBASE
RESET
GENERATOR
MR
V
CC
70
m
A
V
CC
Figure 1. ADM706 Functional Block Diagram
1.25V
V
REF
*
POWER FAIL
INPUT (PFI)
POWER FAIL
OUTPUT (
PFO
)
RESET
*
VOLTAGE REFERENCE = 2.63V (R), 2.93V (S), 3.08V (T)
ADM708
RESET
GENERATOR
MR
V
CC
70
m
A
V
CC
RESET
Figure 2. ADM708 Functional Block Diagram
CIRCUIT INFORMATION
Power Fail Reset
The reset output provides a reset (
RESET
or RESET) output
signal to the Microprocessor whenever the V
CC
input is below
the reset threshold. The actual reset threshold voltage is depen-
dent on whether a P/R, S, or T suffix device is used. An internal
timer holds the reset output active for 200 ms after the voltage
on V
CC
rises above the threshold. This is intended as a power-on
reset signal for the microprocessor. It allows time for both the
power supply and the microprocessor to stabilize after power-
up. If a power supply brownout or interruption occurs, the reset
line is similarly activated and remains active for 200 ms after the
supply recovers. If another interruption occurs during an active
reset period, then the reset timeout period continues for an ad-
ditional 200 ms.
The reset output is guaranteed to remain valid with V
CC
as low
as 1 V. This ensures that the microprocessor is held in a stable
shutdown condition as the power supply starts up.
The ADM706P provides an active high reset (RESET) signal;
the ADM706R/S/T provides an active low (
RESET
) signal;
while the ADM708R/S/T provides both RESET and
RESET
.
Manual Reset
The manual reset input (
MR
) allows other reset sources such as
a manual reset switch to generate a processor reset. The input is
effectively debounced by the timeout period (200 ms typical).
The
MR
input is TTL/CMOS compatible so it may also be
driven by any logic reset output. If unused, the
MR
input may
be tied high or left floating.
V
CC
RESET
MR
WDO
VRT
VRT
t
RS
t
RS
MR
EXTERNALLY
DRIVEN LOW
NOTE: RESET = COMPLEMENT OF
RESET
Figure 3.
RESET
,
MR
and
WDO
Timing
Watchdog Timer (ADM706)
The watchdog timer circuit may be used to monitor the activity
of the microprocessor in order to check that it is not stalled in
an indefinite loop. An output line on the processor is used to
toggle the Watchdog Input (WDI) line. If this line is not toggled
within the timeout period (1.6 sec), the watchdog output
(
WDO
) is driven low. The
WDO
output may be connected to a
nonmaskable interrupt (NMI) on the processor. Therefore, if
the watchdog timer times out, an interrupt is generated. The in-
terrupt service routine should then be used to rectify the
problem.
The watchdog timer is cleared by either a high-to-low or by a
low-to-high transition on WDI. Pulses as narrow as 50 ns are
detected. The timer is also cleared by RESET/
RESET
going
active. Therefore the watchdog timeout period begins after reset
goes inactive.
When V
CC
falls below the reset threshold,
WDO
is forced low
whether or not the watchdog timer has timed out. Normally
this would generate an interrupt but it is overridden by RESET/
RESET
going active.
The watchdog monitor can be deactivated by floating the
Watchdog Input (WDI). The
WDO
output can now be used as
a low line output since it will only go low when V
CC
falls below
the reset threshold.
t
WP
t
WD
WDI
WDO
RESET
t
RS
RESET EXTERNALLY
TRIGGERED BY
MR
t
WD
t
WD
Figure 4. Watchdog Timing
相關PDF資料 |
PDF描述 |
|---|---|
| ADM708RAN | ECONOLINE: REC3-S_DRW(Z)/H* - 3W DIP Package- 1kVDC Isolation- Wide Input 2:1 & 4:1- Regulated Output- 100% Burned In- UL94V-0 Package Material- Continuous Short Circiut Protection- Efficiency to 80% |
| ADM708RAR | +3 V, Voltage Monitoring uP Supervisory Circuits |
| ADM708SAN | +3 V, Voltage Monitoring uP Supervisory Circuits |
| ADM708SAR | +3 V, Voltage Monitoring uP Supervisory Circuits |
| ADM708T | Analog Switch / Multiplexer (Mux) IC; On-Resistance, Rds(on):100ohm; Analog Switch Function:SPST; No. of Channels:4; Leakage Current:1nA; Supply Voltage Max:44V; Package/Case:16-DIP; Leaded Process Compatible:No RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM708RAN | 制造商:Analog Devices 功能描述:Processor Supervisor 2.63V 2.63V 8-Pin PDIP 制造商:Analog Devices 功能描述:PROCESSOR SUPERVISOR 2.63V 350UA 8PDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:RESET GENERATOR I.C. - Bulk |
| ADM708RANZ | 功能描述:IC SUPERVISOR MPU 2.63V WD 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:400 系列:- 類型:備用電池電路 監視電壓數目:1 輸出:開路漏極，推挽式 復位:高有效/低有效 復位超時:最小為 35 ms 電壓 - 閥值:4.65V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:帶卷 (TR) 其它名稱:ADM691ARZ-REEL7TR |
| ADM708RAR | 功能描述:IC SUPERVISOR MPU 2.63V WD 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:400 系列:- 類型:備用電池電路 監視電壓數目:1 輸出:開路漏極，推挽式 復位:高有效/低有效 復位超時:最小為 35 ms 電壓 - 閥值:4.65V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:帶卷 (TR) 其它名稱:ADM691ARZ-REEL7TR |
| ADM708RAR-REEL | 功能描述:IC SUPERVISOR MPU 2.63V WD 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:400 系列:- 類型:備用電池電路 監視電壓數目:1 輸出:開路漏極，推挽式 復位:高有效/低有效 復位超時:最小為 35 ms 電壓 - 閥值:4.65V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC W 包裝:帶卷 (TR) 其它名稱:ADM691ARZ-REEL7TR |
| ADM708RARZ | 功能描述:IC SUPERVISOR MPU 2.63V WD 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 其它有關文件:STM6717 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:2 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 600 ms 電壓 - 閥值:1.11V，3.075V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 產品目錄頁面:1194 (CN2011-ZH PDF) 其它名稱:497-7019-6 |
發布緊急采購，3分鐘左右您將得到回復。