- 您現在的位置：買賣IC網 > PDF目錄374015 > ADM8691ARN (ANALOG DEVICES INC) Microprocessor Supervisory Circuits PDF資料下載
參數資料
| 型號： | ADM8691ARN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Microprocessor Supervisory Circuits |
| 中文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| 封裝： | MS-012AC, SOIC-16 |
| 文件頁數： | 4/16頁 |
| 文件大小： | 207K |
| 代理商： | ADM8691ARN |
ADM8690–ADM8695
REV. 0
–4–
PIN FUNCT ION DE SCRIPT ION
Mnemonic
Function
V
CC
V
BAT T
V
OUT
Power Supply Input: +5 V Nominal.
Backup Battery Input.
Output Voltage, V
CC
or V
BAT T
is internally switched to V
OUT
depending on which is at the highest potential. V
OUT
can supply up to 100 mA to power CMOS RAM. Connect V
OUT
to V
CC
if V
OUT
and V
BAT T
are not used.
0 V. Ground reference for all signals.
Logic Output.
RESET
goes low if
1. V
CC
falls below the Reset T hreshold
2. T he watchdog timer is not serviced within its timeout period.
T he reset threshold is typically 4.65 V for the ADM8690/ADM8691/ADM8694/ADM8695 and 4.4 V for the ADM8692
and ADM8693.
RESET
remains low for 50 ms (ADM8690/ADM8691/ADM8692/ADM8693) or 200 ms (ADM8694/
ADM8695) after V
CC
returns above the threshold.
RESET
also goes low for 50 (200) ms if the watchdog timer is
enabled but not serviced within its timeout period. T he
RESET
pulse width can be adjusted on the ADM8691/ADM8693/
ADM8695 as shown in T able I. T he
RESET
output has an internal 3
μ
A pull up, and can either connect
to an open collector Reset bus or directly drive a CMOS gate without an external pull-up resistor.
Watchdog Input. WDI is a three level input. If WDI remains either high or low for longer than the watchdog timeout
period,
RESET
pulses low and WDO goes low. T he timer resets with each transition on the WDI line. T he watchdog
timer may be disabled if WDI is left floating or is driven to midsupply.
Power Fail Input. PFI is the noninverting input to the Power Fail Comparator when PFI is less than 1.3 V,
PFO
goes low. Connect PFI to GND or V
OUT
when not used.
Power Fail Output.
PFO
is the output of the Power Fail Comparator. It goes low when PFI is less than 1.3 V. T he
comparator is turned off and
PFO
goes low when V
CC
is below V
BAT T
.
Logic Input. T he input to the
CE
gating circuit. Connect to GND or V
OUT
if not used.
Logic Output.
CE
OUT
is a gated version of the
CE
IN
signal.
CE
OUT
tracks
CE
IN
when V
CC
is above the reset
threshold. If V
CC
is below the reset threshold,
CE
OUT
is forced high. See Figures 5 and 6.
Logic Output. BAT T ON goes high when V
OUT
is internally switched to the V
BAT T
input. It goes low when V
OUT
is internally switched to V
CC
. T he output typically sinks 35 mA and can directly drive the base of an external
PNP transistor to increase the output current above the 100 mA rating of V
OUT
.
Logic Output.
LOW LINE
goes low when V
CC
falls below the reset threshold. It returns high as soon as V
CC
rises
above the reset threshold.
Logic Output. RESET is an active high output. It is the inverse of
RESET
.
Logic Oscillator Select Input. When OSC SEL is unconnected (floating) or driven high, the internal oscillator sets
the reset active time and watchdog timeout period. When OSC SEL is low, the external oscillator input, OSC IN,
is enabled. OSC SEL has a 3
μ
A internal pull-up (see T able I).
Oscillator Logic Input. With OSC SEL low, OSC IN can be driven by an external clock signal or an external
capacitor can be connected between OSC IN and GND. T his sets both the reset active pulse timing and the watch-
dog timeout period (see T able I and Figure 4). With OSC SEL high or floating, the internal oscillator is enabled
and the reset active time is fixed at 50 ms typ. (ADM8691/ADM8693) or 200 ms typ (ADM8695). In this mode the
OSC IN pin selects between fast (100 ms) and slow (1.6 s) watchdog timeout periods. In both modes, the timeout
period immediately after a reset is 1.6 s typical.
Logic Output. T he Watchdog Output,
WDO
, goes low if WDI remains either high or low for longer than the
watchdog timeout period.
WDO
is set high by the next transition at WDI. If WDI is unconnected or at midsupply,
the watchdog timer is disabled and
WDO
remains high.
WDO
also goes high when
LOW LINE
goes low.
GND
RESET
WDI
PFI
PFO
CE
IN
CE
OUT
BAT T ON
LOW LINE
RESET
OSC SEL
OSC IN
WDO
相關PDF資料 |
PDF描述 |
|---|---|
| ADM8691ARU | Microprocessor Supervisory Circuits |
| ADM8691ARW | Microprocessor Supervisory Circuits |
| ADM8693ARN | Thyristor Module; Current, It av:250A; Repetitive Reverse Voltage Max, Vrrm:1600V; Peak Surge Current:8800A; di/dt:800A/ s; Package/Case:ND44; Peak Reflow Compatible (260 C):Yes; Current Rating:250A |
| ADM8693ARU | Thyristor Diode Module; Repetitive Reverse Voltage Max, Vrrm:1800V; Leaded Process Compatible:Yes; Voltage Rating:1800V RoHS Compliant: Yes |
| ADM8693ARW | THYRISTOR MODULE,SCR DOUBLER,1.2kV V(RRM),700A I(T) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM8691ARN-REEL | 功能描述:IC SUPERVSR MPU 4.65V ADJ 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM8691ARNZ | 功能描述:IC SUPERVSR MPU 4.65V ADJ 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM8691ARU | 功能描述:IC SUPERVSR MPU 4.65V ADJ16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM8691ARU-REEL | 功能描述:IC SUPERVSR MPU 4.65V ADJ16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM8691ARUZ | 功能描述:IC SUPERVSR MPU 4.65V ADJ16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
發布緊急采購，3分鐘左右您將得到回復。