- 您現在的位置：買賣IC網 > PDF目錄374017 > ADN2849ACP-RL (ANALOG DEVICES INC) 10.7 Gbps Electro-Absorption Modulator Driver PDF資料下載
參數資料
| 型號： | ADN2849ACP-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 其它接口 |
| 英文描述： | 10.7 Gbps Electro-Absorption Modulator Driver |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PQCC24 |
| 封裝： | 4 X 4 MM, PLASTIC, MO-220VGGD-2, LFCSP-24 |
| 文件頁數： | 16/17頁 |
| 文件大小： | 1425K |
| 代理商： | ADN2849ACP-RL |
ADN2849
DESIGN EXAMPLE
This section describes a design example that covers the
followings:
Rev. Pr. G | Page 16 of 17
Headroom calculation for the required bias offset and
modulation voltages
Required voltage range at the BIAS_SET and
MOD_SET pins to generate the required bias offset
and modulation voltages
This design example assumes a -5.2V supply voltage, 0.5V bias
offset voltage and 2V modulation voltage.
Headroom calculations
In order to operate properly, the bias offset and modulation
voltages must satisfy the following condition:
min
MODP
V
ffset
O
Bias
Modulation
V
VEE
V
≤
+
Assuming that V
MODPmin
=1.7V (see table1), the above condition
became:
V
5
7
2
V
5
=
≤
BIAS_SET voltage range
The voltage range at the BIAS_SET pin to generate 0.5V bias
offset voltage at the MODP pin can be calculated using the
BIAS_SET voltage to bias offset voltage gain specification from
table1 using the formulae:
min
OFFSET
K
BIAS
max
SET
_
BIAS
max
OFFSET
BIAS
K
min
SET
_
BIAS
V
V
V
V
=
=
Where K
min
and K
max
are the minimum and maximum values of
the BIAS_SET voltage to offset bias voltage gain from table1.
Substituting the values the BIAS_SET voltage range is 0.45V to
0.55V.
MOD_SET voltage range
The voltage range at the MOD_SET pin to generate 2V bias
offset voltage at the MODP pin can be calculated using the
MOD_SET voltage to bias offset voltage gain specification from
table1 using the formulae:
min
MODULATION
K
max
SET
_
MOD
max
MODULATION
K
min
SET
_
MOD
V
V
V
V
=
=
Where K
min
and K
max
are the minimum and maximum values of
the MOD_SET voltage to offset bias voltage gain from table1.
Substituting the values the MOD_SET voltage range is 1.05V to
1.33V.
Preliminary Technical Data
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2849ACP-RL7 | 10.7 Gbps Electro-Absorption Modulator Driver |
| ADN2849SURF | 10.7 Gbps Electro-Absorption Modulator Driver |
| ADN2850ACP25 | Nonvolatile Memory, Dual 1024 Position Programmable Resistors |
| ADN2850ACP25-RL7 | Nonvolatile Memory, Dual 1024 Position Programmable Resistors |
| ADN2850ACP250 | TERM,RING NON-INSUL. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2849ACP-RL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10.7 Gbps Electro-Absorption Modulator Driver |
| ADN2849SURF | 制造商:AD 制造商全稱:Analog Devices 功能描述:10.7 Gbps Electro-Absorption Modulator Driver |
| ADN2850 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory, Dual 1024 Position Programmable Resistors |
| ADN2850ACP25 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory, Dual 1024 Position Programmable Resistors |
| ADN2850ACP250 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory, Dual 1024 Position Programmable Resistors |
發布緊急采購，3分鐘左右您將得到回復。