- 您現在的位置：買賣IC網 > PDF目錄374017 > ADN2870ACPZ-RL7 (ANALOG DEVICES INC) 3.3 V Dual-Loop, 50 Mbps to 3.3 Gbps Laser Diode Driver PDF資料下載
參數資料
| 型號： | ADN2870ACPZ-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 其它接口 |
| 英文描述： | 3.3 V Dual-Loop, 50 Mbps to 3.3 Gbps Laser Diode Driver |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, QCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, MO-220VGGD-2, LFCSP-24 |
| 文件頁數： | 12/20頁 |
| 文件大小： | 764K |
| 代理商： | ADN2870ACPZ-RL7 |
ADN2870
Operation with Lasers with Temperature-Dependent
Nonlinearity of Laser LI Curve
The ADN2870 ERCL extracts information from the monitor
photodiode signal relating to the slope of the LI characteristics
at the optical 1 level (P1). For lasers with good linearity over
temperature, the slope measured by the ADN2870 at the optical
1 level is representative of the slope anywhere on the LI curve.
This slope information is used to set the required modulation
current to achieve the required optical extinction ratio.
Rev. 0 | Page 12 of 20
0
0.5
3.0
2.5
2.0
1.5
1.0
4.0
3.5
20
40
CURRENT (mA)
60
O
100
80
0
RELATIVELY LINEAR LI CURVE AT 25°C
NONLINEAR LI CURVE AT 80°C
0
Figure 25. Measurement of a Laser LI Curve Showing
Laser Nonlinearity at High Temperatures
Some types of laser have LI curves that become progressively
more nonlinear with increasing temperature (see Figure 25). At
temperatures where the LI curve shows significant nonlinearity,
the LI curve slope measured by the ADN2870 at the optical 1
level is no longer representative of the overall LI curve. It is
evident that applying a modulation current based on this slope
information cannot maintain a constant extinction ratio over
temperature. However, the ADN2870 can be configured to
maintain near constant optical bias and extinction ratio with a
laser exhibiting a monotonic temperature-dependant nonlinear-
ity. To implement this correction, it is necessary to characterize
a small sample of lasers for their typical nonlinearity by
measuring them at two temperature points, typically 25°C and
85°C. The measured nonlinearity is used to determine the
amount of feedback to apply. Typically one must characterize 5
to 10 lasers of a particular model to get a good number. Then
the product can be calibrated at 25°C only, avoiding the expense
of temperature calibration. Typically the microcontroller
supervisor is used to measure the laser and apply the feedback.
This scheme is particularly suitable for circuits that already use
a microcontroller for control and digital diagnostic monitoring.
The ER correction scheme, while using the average nonlinearity
for the laser population, in fact, supplies a corrective measure-
ment based on each laser’s actual performance as measured
during operation. The ER correction scheme corrects for errors
due to laser nonlinearity while the dual loop continues to adjust
for changes in the Laser LI.
For more details on maintaining average optical power and
extinction ratio over temperature when working with lasers
displaying a temperature dependant nonlinearity of LI curve,
see Application Note AN-743.
CONTROL
The ADN2870 has two methods for setting the average power
(PAV) and extinction ratio (ER). The average power and
extinction ratio can be voltage-set using a microcontroller’s
voltage DACs outputs to provide controlled reference voltages
PAVREF and ERREF. Alternatively, the average power and
extinction ratio can be resistor-set using potentiometers at the
PAVSET and ERSET pins, respectively.
VOLTAGE SETPOINT CALIBRATION
The ADN2870 allows interface to a microcontroller for both
control and monitoring (see Figure 26). The average power at
the PAVSET pin and extinction ratio at the ERSET pin can be
set using the microcontroller’s DACs to provide controlled
reference voltages PAVREF and ERREF. Note that during power
up, there is an internal sequence that allows 25 ms before
enabling the alarms; therefore the customer must ensure that
the voltage for PAVREF and ERREF are active within 20 ms.
RPAV
R
P
PAVREF
SP
AV
×
×
=
(Volts)
AV
P
CW
P
CW
MPD
ERSET
ER
ER
I
R
ERREF
×
+
×
×
=
1
1
_
(Volts)
where:
R
SP
is the monitor photodiode responsivity.
P
CW
is the dc optical power specified on the laser data sheet.
I
MPD_CW
is MPD current at that specified P
CW
.
P
AV
is the average power required.
ER
is the desired extinction ratio (
ER
= P1/P0).
In voltage setpoint, RPAV and R
ERSET
must be 1 k resistors with
a 1% tolerance and a temperature coefficient of 50 ppm/°C.
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2890 | 3.3 V 2.7 Gb/s Limiting Amplifier |
| ADN2890ACP | 3.3 V 2.7 Gb/s Limiting Amplifier |
| ADN2890ACP-RL | 3.3 V 2.7 Gb/s Limiting Amplifier |
| ADN2890ACP-RL7 | 3.3 V 2.7 Gb/s Limiting Amplifier |
| ADN8810 | 12-Bit High Output Current Source |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2871 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.3 V, 50 Mbps to 4.25 Gbps Single-Loop Laser Diode Driver |
| ADN2871ACPZ | 功能描述:IC LASER DRIVER 4.25GBPS 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2871ACPZ-RL | 功能描述:IC LASER DRIVER 4.25GBPS 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2871ACPZ-RL7 | 功能描述:IC LASER DRIVER 4.25GBPS 24LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| ADN2872 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3.3 V Dual-Loop, 50 Mbps to 3.3 Gbps Laser Diode Driver |
發布緊急采購，3分鐘左右您將得到回復。