- 您現在的位置：買賣IC網 > PDF目錄374018 > ADP1073AR-5 (ANALOG DEVICES INC) Circular Connector; No. of Contacts:55; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:23; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:23-55 PDF資料下載
參數資料
| 型號： | ADP1073AR-5 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Circular Connector; No. of Contacts:55; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:23; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:23-55 |
| 中文描述： | 0.4 A SWITCHING REGULATOR, 23 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 442K |
| 代理商： | ADP1073AR-5 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
ADP1073
–5–
REV. 0
TEMPERATURE –
8
C
2300
2100
1100
2
40
0
85
25
70
1900
1700
1500
1300
V
IN
= 1.5V
R
L
= 100k
V
G
Figure 11. “Gain Block” Gain vs. Temperature
THEORY OF OPERATION
The ADP1073 is a flexible, low power switch mode power
supply (SMPS) controller. The regulated output voltage can be
greater than the input voltage (boost or step-up mode) or less
than the input (buck or step-down mode). This device uses a
gated-oscillator technique to provide very high performance
with low quiescent current.
A functional block diagram of the ADP1073 is shown on the
front page. The internal 212 mV reference is connected to one
input of the comparator, while the other input is externally
connected (via the FB pin) to a feedback network connected to
the regulated output. When the voltage at the FB pin falls below
212 mV, the 19 kHz oscillator turns on. A driver amplifier pro-
vides base drive to the internal power switch and the switching
action raises the output voltage. When the voltage at the FB pin
exceeds 212 mV, the oscillator is shut off. While the oscillator is
off, the ADP1073 quiescent current is only 100
μ
A. The com-
parator includes a small amount of hysteresis, which ensures
loop stability without requiring external components for fre-
quency compensation.
The maximum current in the internal power switch can be set
by connecting a resistor between V
IN
and the I
LIM
pin. When
the maximum current is exceeded, the switch is turned OFF.
The current limit circuitry has a time delay of about 2
μ
s. If an
external resistor is not used, connect I
LIM
to V
IN
. Further infor-
mation on I
LIM
is included in the Limiting the Switch Current
section of this data sheet.
The ADP1073 internal oscillator provides 38
μ
s ON and 15
μ
s
OFF times, which is ideal for applications where the ratio be-
tween V
IN
and V
OUT
is roughly a factor of three (such as gener-
ating +5 V from a single 1.5 V cell). Wider range conversions,
as well as step-down converters, can also be accomplished with
a slight loss in the maximum output power that can be obtained.
An uncommitted gain block on the ADP1073 can be connected
as a low-battery detector, linear post-regulator or undervoltage
lockout detector. The inverting input of the gain block is inter-
nally connected to the 212 mV reference. The noninverting
input is available at the SET pin. A resistor divider, connected
between V
IN
and GND with the junction connected to the SET
pin, causes the AO output to go LOW when the input voltage
goes below the low battery set point. The AO output is an open
collector NPN transistor that can sink 100
μ
A.
The ADP1073 provides external connections for both the col-
lector and emitter of its internal power switch, which permits
both step-up and step-down modes of operation. For the step-
up mode, the emitter (Pin SW2) is connected to GND and the
collector (Pin SW1) drives the inductor. For step-down mode,
the emitter drives the inductor while the collector is connected
to V
IN
.
The output voltage of the ADP1073 is set with two external
resistors. Three fixed-voltage models are also available:
ADP1073-3.3 (+3.3 V), ADP1073-5 (+5 V) and ADP1073-12
(+12 V). The fixed-voltage models are identical to the ADP1073,
except that laser-trimmed voltage-setting resistors are included
on the chip. Only three external components are required to
form a +3.3 V, +5 V or +12 V converter. On the fixed-voltage
models of the ADP1073, simply connect the feedback pin (Pin
8) directly to the output voltage.
The ADP1073 oscillator only turns on when the output voltage
is below the programmed voltage. When the output voltage is
above the programmed voltage, the ADP1073 remains in its
quiescent state to conserve power. Output ripple, which is in-
herent in gated oscillator converters, is typically 125 mV for a
5 V output and 300 mV for a 12 V output. This ripple voltage
can be greatly reduced by inserting the gain-block between the
output and the FB pin. Further information and a typical circuit
are shown in the Programming the Gain Block section.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP1108 | Circular Connector; No. of Contacts:19; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:25-19 |
| ADP1108AN | Circular Connector; No. of Contacts:19; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:25-19 |
| ADP1108AN-12 | Circular Connector; No. of Contacts:128; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:25-1 |
| ADP1108AN-33 | Circular Connector; No. of Contacts:128; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:25-1 |
| ADP1108AN-5 | Circular Connector; No. of Contacts:30; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:25-20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1074ARWZ | 功能描述:ISOLATED ACTIVE CLAMP FOR 制造商:analog devices inc. 系列:* 包裝:管件 零件狀態:在售 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:24-SOIC 標準包裝:31 |
| ADP1074ARWZ-R7 | 功能描述:ISOLATED ACTIVE CLAMP FOR 制造商:analog devices inc. 系列:* 包裝:剪切帶（CT） 零件狀態:在售 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:24-SOIC 標準包裝:1 |
| ADP1074ARWZ-RL | 功能描述:ISOLATED ACTIVE CLAMP FOR 制造商:analog devices inc. 系列:* 包裝:帶卷（TR） 零件狀態:在售 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:24-SOIC 標準包裝:1,000 |
| ADP1074-EVALZ | 功能描述:ADP1074 EVALUATION BOARD 制造商:analog devices inc. 系列:- 零件狀態:在售 主要用途:DC/DC 轉換器 輸出和類型:1，隔離 電壓 - 輸出:12.1V 電流 - 輸出:6A 電壓 - 輸入:36 V ~ 60 V 穩壓器拓?fù)?正向轉換器 頻率 - 開關:291kHz 板類型:完全填充 所含物品:板 使用的 IC/零件:ADP1074 備注:- 標準包裝:1 |
| ADP10FN | 制造商:TE Connectivity 功能描述:SWITCH DIL PIANO 10 WAY |
發布緊急采購，3分鐘左右您將得到回復。