- 您現在的位置：買賣IC網 > PDF目錄374019 > ADP3155JRU (ANALOG DEVICES INC) 5-Bit Programmable Triple Power Supply Controller for Pentium III Processors PDF資料下載
參數資料
| 型號： | ADP3155JRU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 5-Bit Programmable Triple Power Supply Controller for Pentium III Processors |
| 中文描述： | SWITCHING CONTROLLER, PDSO20 |
| 封裝： | TSSOP-20 |
| 文件頁數： | 8/14頁 |
| 文件大小： | 200K |
| 代理商： | ADP3155JRU |
REV. A
ADP3155
–8–
Transient tolerance (for less than 2
μ
s) of the supply voltage for
the processor core when the load changes between the mini-
mum and maximum values with a di/dt of 30 A/
μ
s:
V
OTR+
= 130 mV
V
OTR–
= –130 mV
Input current di/dt when the load changes between the mini-
mum and maximum values: less than 0.1 A/
μ
s
The above requirements correspond to Intel’s published power
supply requirements based on VRM 8.2 guidelines.
C
T
Selection for Operating Frequency
The ADP3155 uses a constant-off-time architecture with t
OFF
determined by an external timing capacitor C
T
. Each time the
high side N-channel MOSFET switch turns on, the voltage
across C
T
is reset to approximately 3.3 V. During the off time,
C
T
is discharged by a constant current of 65
μ
A. Once C
T
reaches 2.3 V, a new on-time cycle is initiated. The value of the
off-time is calculated using the continuous-mode operating
frequency. Assuming a nominal operating frequency of f
NOM
=
200 kHz at an output voltage of 2.8 V, the corresponding off
time is:
V
OFF
IN
t
V
f
s
O
NOM
=
=
1
1
2 2
.
μ
–
The timing capacitor can be calculated from the equation:
C
t
A
V
pF
T
OFF
=
×
1
=
65
143
μ
The converter operates at the nominal operating frequency only
at the above specified V
OUT
and at light load. At higher V
OUT
or
heavy load, the operating frequency decreases due to the para-
sitic voltage drops across the power devices. The actual mini-
mum frequency at V
OUT
= 2.8 V is calculated to be 160 kHz (see
Equation 1), where:
I
IN
is the input dc current
(assuming an efficiency of 90%, I
IN
= 9 A)
R
IN
is the resistance of the input filter
(estimated value: 7 m
)
R
DS(ON)HSF
is the resistance of the high side MOSFET
(estimated value: 10 m
)
R
DS(ON)LSF
is the resistance of the low side MOSFET
(estimated value: 10 m
)
R
SENSE
is the resistance of the sense resistor
(estimated value: 7 m
)
R
L
is the resistance of the inductor
(estimated value: 6 m
)
f
t
V
–
I
R
–
I
R
R
R
R
–
V
V
I
R
I
R
R
R
kHz
MIN
OFF
IN
IN
IN
OMAX
(
DS ON HSF
(
SENSE
+
L
O
IN
IN
IN
OMAX
DS ON HSF
(
SENSE
L
DS ON LSF
(
=
×
+
+
+
=
1
160
–
–
(
)–
)
)
)
)
(1)
C
OUT
Selection—Determining the ESR
The required ESR and capacitance drive the selection of the
type and quantity of the output capacitors. The ESR must be
small enough that both the resistive voltage deviation due to a
step change in the load current and the output ripple voltage
stay below the values defined in the specification of the supplied
microprocessor. The capacitance must be large enough that the
output is held up while the inductor current ramps up or down
to the value corresponding to the new load current.
The total static tolerance of the Pentium II processor is 160 mV.
Taking into account the
±
1% setpoint accuracy of the ADP3155,
and assuming a 0.5% (or 14 mV) peak-to-peak ripple, the allowed
static voltage deviation of the output voltage when the load
changes between the minimum and maximum values is 80 mV.
Assuming a step change of
I = I
OMAX
–I
OMIN
= 13.4 A, and
allocating all of the total allowed static deviation to the contri-
bution of the ESR sets the following limit:
R
ESR
mV
A
m
E MAX
(
MAX
)
.
.
=
=
=
1
80
13 4
5 9
The output filter capacitor must have an ESR of less than 5.9 m
.
One can use, for example, six FA-type capacitors from
Panasonic, with 2700
μ
F capacitance, 10 V voltage rating, and
34 m
ESR. The six capacitors have a total ESR of 5.7 m
when
connected in parallel, which gives adequate margin.
Inductor Selection
The minimum inductor value can be calculated from ESR, off-
time, dc output voltage and allowed peak-to-peak ripple voltage.
L
V t
R
V
V
s
m
mV
H
MIN
E MAX
(
RIPPLE p
p
1
2 8
.
2 2
14
5 9
.
2 6
.
=
=
×
×
=
)
,
.
μ
μ
The minimum inductance gives a peak-to-peak ripple current of
2.15 A, or 15% of the maximum dc output current I
OMAX
.
The inductor peak current in normal operation is:
I
LPEAK
=
I
OMAX
+
I
RPP
/2 = 15.3
A
The inductor valley current is:
I
LVALLEY
=
I
LPEAK
–
I
RPP
= 13
A
The inductor for this application should have an inductance
of 2.6
μ
H at full load current and should not saturate at the
worst-case overload or short circuit current at the maximum
specified ambient temperature. A suitable inductor is the
CTX12-13855 from Coiltronics, which is 4.4
μ
H at 1 A and
about 2.5
μ
H at 14.2 A.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3156JR-15 | Dual Power Supply Controller for Desktop Systems |
| ADP3156JR-18 | Dual Power Supply Controller for Desktop Systems |
| ADP3156JR-25 | Dual Power Supply Controller for Desktop Systems |
| ADP3156 | Dual Power Supply Controller for Desktop Systems |
| ADP3160 | 5-Bit Programmable 2-Phase Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3155JRU-REEL | 制造商:Rochester Electronics LLC 功能描述:5-BIT PROGRAMMBLE TRIPLE POWER SUPPLY - Tape and Reel |
| ADP3155JRU-REEL7 | 功能描述:IC PS TRPL PENTIUM III 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| ADP3156 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Power Supply Controller for Desktop Systems |
| ADP3156JR-1.5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADP3156JR-1.5-REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。