- 您現在的位置：買賣IC網 > PDF目錄374022 > ADP3338AKC-33 (Analog Devices, Inc.) JT 55C 55#20 PIN RECP PDF資料下載
參數資料
| 型號： | ADP3338AKC-33 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | JT 55C 55#20 PIN RECP |
| 中文描述： | 高精度超低智商，一甲，anyCAP低壓差穩壓器 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 144K |
| 代理商： | ADP3338AKC-33 |
REV. 0
ADP3338
–7–
THERMAL OVERLOAD PROTECTION
The ADP3338 is protected against damage due to excessive power
dissipation by its thermal overload protection circuit. Thermal
protection limits the die temperature to a maximum of 160
°
C.
Under extreme conditions (i.e., high ambient temperature and
power dissipation) where the die temperature starts to rise above
160
°
C, the output current will be reduced until the die tempera-
ture has dropped to a safe level.
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For normal
operation, the device’s power dissipation should be externally
limited so that the junction temperature will not exceed 150
°
C.
CALCULATING POWER DISSIPATION
Device power dissipation is calculated as follows:
(
Where
I
LOAD
and
I
GND
are load current and ground current,
V
IN
and
V
OUT
are the input and output voltages respectively.
Assuming worst-case operating conditions are I
LOAD
= 1.0 A,
I
GND
= 10 mA, V
IN
= 3.3 V and V
OUT
= 2.5 V, the device power
dissipation is:
D
=
(
3 3
2 5
1000
.
–
.
So, for a junction temperature of 125
°
C and a maximum ambi-
ent temperature of 85
°
C, the required thermal resistance from
junction to ambient is:
P
V
V
I
V
I
D
IN
OUT
LOAD
IN
GND
=
)
×
+
(
)
×
P
V
V
mA
V
mA
mW
)
+
(
)
=
3 3
.
10
833
θ
JA
=
°
.
°
=
°
125
85
W
0 833
48
C
C
C W
/
–
PRINTED CIRCUIT BOARD LAYOUT
CONSIDERATIONS
The SOT-223
’
s thermal resistance,
θ
JA
, is determined by the
sum of the junction-to-case and the case-to-ambient thermal
resistances. The junction-to-case thermal resistance,
θ
JC
, is
determined by the package design and specified at 26.8
°
C/W.
However, the case-to-ambient thermal resistance is determined
by the printed circuit board design.
As shown in Figures 4a
–
c, the amount of copper the ADP3338
is mounted to affects the thermal performance. When mounted
to 2 oz. copper with just the minimal pads, Figure 4a, the
θ
JA
is
126.6
°
C/W. By adding a small copper pad under the ADP3338,
Figure 4b, reduces the
θ
JA
to 102.9
°
C/W. Increasing the copper
pad to 1 square inch, Figure 4c, reduces the
θ
JA
even further
to 52.8
°
C/W.
a.
b.
c.
Figure 4. PCB Layouts
Use the following general guidelines when designing printed
circuit boards:
1. Keep the output capacitor as close to the output and ground
pins as possible.
2. Keep the input capacitor as close to the input and ground
pins as possible.
3. PC board traces with larger cross sectional areas will remove
more heat from the ADP3338. For optimum heat transfer,
specify thick copper and use wide traces.
4. The thermal resistance can be decreased by adding a copper
pad under the ADP3338 as shown in Figure 4b.
5. If possible, utilize the adjacent area to add more copper
around the ADP3338. Connecting the copper area to the
output of the ADP3338, as shown in Figure 4c, is best but
will improve thermal performance even if it is connected to
other signals.
6. Use additional copper layers or planes to reduce the thermal
resistance. Again, connecting the other layers to the output
of the ADP3338 is best, but not necessary. When connecting
the output pad to other layers use multiple vias.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3338AKC-5 | CONNECTOR |
| ADP3339AKC-18 | JT 85C 85#22 PIN RECP |
| ADP3339 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADP3339AKC-25 | Circular Connector; No. of Contacts:85; Series:MS27474; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:22; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:22-2 RoHS Compliant: No |
| ADP3339AKC-285 | JT 100C 100#22D SKT RECP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3338AKC-3-RL | 功能描述:IC REG LDO 3V 1A SOT223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:anyCAP® 產品培訓模塊:More Information on LDOs 標準包裝:50 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.3V 輸入電壓:最高 15V 電壓 - 壓降（標準）:1.1V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最小）:800mA 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-4，D²Pak（3 引線+接片），TO-263AA 供應商設備封裝:D2PAK-3 包裝:管件 |
| ADP3338AKC-3-RL7 | 制造商:Analog Devices 功能描述:LDO Regulator Pos 3V 1.6A 4-Pin(3+Tab) SOT-223 T/R |
| ADP3338AKC-5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High-Accuracy Ultralow IQ, 1 A, anyCAP Low Dropout Regulator |
| ADP3338AKC-5-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Accuracy, Ultralow IQ, 1A, anyCAP Low Dropout Regulator |
| ADP3338AKC-5-REEL7 | 功能描述:IC REG LDO 5V 1A SOT-223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:anyCAP® 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式和可調式 輸出電壓:3.3V，1.25 V ~ 5.7 V 輸入電壓:4.5 V ~ 7 V 電壓 - 壓降（標準）:1.1V @ 1A 穩壓器數量:2 電流 - 輸出:1A 電流 - 限制（最小）:1A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-252-5，DPak（4 引線 + 接片），TO-252AD 供應商設備封裝:PPAK 包裝:管件 其它名稱:497-3576-5 |
發布緊急采購，3分鐘左右您將得到回復。