- 您現在的位置：買賣IC網 > PDF目錄374028 > ADR439A (Analog Devices, Inc.) Ultralow Noise XFET Voltage References with Current Sink and Source Capability PDF資料下載
參數資料
| 型號： | ADR439A |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Ultralow Noise XFET Voltage References with Current Sink and Source Capability |
| 中文描述： | 超低噪聲XFET電壓基準與電流吸入和源能力 |
| 文件頁數： | 16/24頁 |
| 文件大小： | 868K |
| 代理商： | ADR439A |
ADR430/ADR431/ADR433/ADR434/ADR435/ADR439
APPLICATIONS
OUTPUT ADJUSTMENT
The ADR43x trim terminal can be used to adjust the output
voltage over a ±0.5% range. This feature allows the system
designer to trim system errors out by setting the reference to a
voltage other than the nominal. This is also helpful if the part is
used in a system at temperature to trim out any error. Adjustment
of the output has negligible effect on the temperature perform-
ance of the device. To avoid degrading temperature coefficients,
both the trimming potentiometer and the two resistors need to
be low temperature coefficient types, preferably <100 ppm/°C.
Rev. B | Page 16 of 24
INPUT
OUTPUT
V
O
= ±0.5%
TRIM
GND
V
IN
R1
470k
R2
10k
(
ADR420)
15k
(
ADR421)
R
P
10k
ADR43x
0
V
O
Figure 31. Output Trim Adjustment
REFERENCE FOR CONVERTERS IN OPTICAL
NETWORK CONTROL CIRCUITS
In the upcoming high capacity, all-optical router network,
Figure 32 employs arrays of micromirrors to direct and route
optical signals from fiber to fiber without first converting them
to electrical form, which reduces the communication speed.
The tiny micromechanical mirrors are positioned so that each is
illuminated by a single wavelength that carries unique informa-
tion and can be passed to any desired input and output fiber.
The mirrors are tilted by the dual-axis actuators controlled by
precision ADCs and DACs within the system. Due to the
microscopic movement of the mirrors, not only is the precision
of the converters important, but the noise associated with these
controlling converters is also extremely critical, because total
noise within the system can be multiplied by the number of
converters employed. As a result, to maintain the stability of the
control loop for this application, the ADR43x is necessary due
to its exceptionally low noise.
GND
SOURCE FIBER
GIMBAL + SENSOR
DESTINATION
FIBER
ACTIVATOR
RIGHT
MEMS MIRROR
LASER BEAM
ACTIVATOR
LEFT
AMPL
PREAMP
AMPL
CONTROL
ELECTRONICS
DAC
ADC
DAC
ADR431
ADR431
ADR431
0
Figure 32. All-Optical Router Network
NEGATIVE PRECISION REFERENCE WITHOUT
PRECISION RESISTORS
In many current-output CMOS DAC applications where the
output signal voltage must be of the same polarity as the
reference voltage, it is often required to reconfigure a current-
switching DAC into a voltage-switching DAC through the use
of a 1.25 V reference, an op amp, and a pair of resistors. Using a
current-switching DAC directly requires an additional opera-
tional amplifier at the output to re-invert the signal. A negative
voltage reference is then desirable from the standpoint that an
additional operational amplifier is not required for either
re-inversion (current-switching mode) or amplification
(voltage-switching mode) of the DAC output voltage. In
general, any positive voltage reference can be converted into a
negative voltage reference through the use of an operational
amplifier and a pair of matched resistors in an inverting
configuration. The disadvantage to this approach is that the
largest single source of error in the circuit is the relative
matching of the resistors used.
A negative reference can easily be generated by adding a
precision op amp and configuring it as shown in Figure 33.
V
OUT
is at virtual ground and, therefore, the negative reference
can be taken directly from the output of the op amp. The op
amp must be dual supply, have low offset and rail-to-rail
capability, if negative supply voltage is close to the reference
output.
相關PDF資料 |
PDF描述 |
|---|---|
| ADR433AR | Ultralow Noise XFET Voltage References with Current Sink and Source Capability |
| ADR430BR-REEL7 | Toggle Switch; Circuitry:SPDT; Switch Operation:On-None-On; Contact Current Max:6A; Actuator Style:Bat; Switch Terminals:Through Hole; Current Rating:6A; Leaded Process Compatible:Yes; Mounting Type:Bracket RoHS Compliant: Yes |
| ADR433BR-REEL7 | Ultralow Noise XFET Voltage References with Current Sink and Source Capability |
| ADR434AR-REEL7 | VARISTOR 140V RMS 20MM RADIAL |
| ADR439BR-REEL7 | Ultralow Noise XFET Voltage References with Current Sink and Source Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADR439AR | 制造商:Analog Devices 功能描述:V-Ref Precision 4.5V 30mA 8-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:4.5 V REFERENCE - Bulk |
| ADR439ARM | 制造商:Analog Devices 功能描述:V-Ref Precision 4.5V 30mA 8-Pin MSOP Tube 制造商:Rochester Electronics LLC 功能描述:4.5 V REFERENCE - Bulk |
| ADR439ARM-REEL7 | 制造商:Analog Devices 功能描述:V-Ref Precision 4.5V 30mA 8-Pin MSOP T/R |
| ADR439ARMZ | 制造商:Analog Devices 功能描述:V-Ref Precision 4.5V 30mA 8-Pin MSOP Tube |
| ADR439ARMZ-REEL7 | 功能描述:IC VREF SERIES PREC 4.5V 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:XFET® 標準包裝:1 系列:- 基準類型:串聯，精度 輸出電壓:4.5V 容差:±800µV 溫度系數:1ppm/°C 輸入電壓:13.5 V ~ 22 V 通道數:1 電流 - 陰極:- 電流 - 靜態:7mA 電流 - 輸出:10mA 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:20-LCC 供應商設備封裝:20-CLCC 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。