- 您現在的位置：買賣IC網 > PDF目錄379646 > ADS-926GC (Electronic Theatre Controls, Inc.) 14-Bit, 500kHz, Low-Power Sampling A/D Converters PDF資料下載
參數資料
| 型號： | ADS-926GC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 串行ADC |
| 英文描述： | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| 中文描述： | 14位，為500kHz，低功耗采樣A / D轉換器 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 151K |
| 代理商： | ADS-926GC |
ADS -926
5
THERMAL REQUIREMENTS
All DATEL sampling A/D converters are fully characterized and
specified over operating temperature (case) ranges of
0 to +70°C and –55 to +125°C. All room-temperature
(T
A
= +25°C) production testing is performed without the use of
heat sinks or forced-air cooling. Thermal impedance figures for
each device are listed in their respective specification tables.
These devices do not normally require heat sinks, however,
standard precautionary design and layout procedures should
be used to ensure devices do not overheat. The ground and
power planes beneath the package, as well as all pcb signal
runs to and from the device, should be as heavy as possible to
help conduct heat away from the package.
Electrically-insulating, thermally-conductive "pads" may be
installed underneath the package. Devices should be soldered
to boards rather than "socketed", and of course, minimal air
flow over the surface can greatly help reduce the package
temperature.
In more severe ambient conditions, the package/junction
temperature of a given device can be reduced dramatically
(typically 35%) by using one of DATEL's HS Series heat sinks.
See Ordering Information for the assigned part number. See
page 1-183 of the DATEL Data Acquisition Components
Catalog for more information on the HS Series. Request
DATEL Application Note AN-8, "Heat Sinks for DIP Data
Converters", or contact DATEL directly, for additional
information.
Figure 4. ADS-926 Timing Diagram
Notes: 1. f
s
= 500kHz.
2. The ADS-926 is a pulse-triggered device. Its internal operations
are triggered by both the rising and falling edges of the start
convert pulse. When sampling at 500kHz, the start pulse must be
between 175 and 225nsec wide. For lower sampling rates, wider
start pulses may be used, however, a 50nsec minimum pulse
width low must be maintained.
START
CONVERT
OUTPUT
DATA
INTERNAL S/H
N
N + 1
Data (N – 1) Valid
Acquisition Time
10ns typ.
Data N Valid (1885ns min.)
EOC
Conversion Time
Invalid
Data
115ns max.
10ns typ.
1390ns ±55ns
35ns max.
Hold
610ns typ.
200ns
±25ns
480ns ±20ns
70ns ±10ns
相關PDF資料 |
PDF描述 |
|---|---|
| ADS-926 | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS926 | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS-926GM | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS-926MC | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS-926MM | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS-926GM | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 500ksps 14-bit Parallel 24-Pin SMT |
| ADS-926MC | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 500ksps 14-bit Parallel 24-Pin CDDIP |
| ADS-926MM | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 500ksps 14-bit Parallel 24-Pin CDDIP |
| ADS-927 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:14-Bit, 1MHz, Low-Power Sampling A/D Converters |
| ADS-927/883 | 制造商:Murata Power Solutions 功能描述:ADC Single 2-Step Flash 1Msps 14-bit Parallel 24-Pin DDIP |
發布緊急采購，3分鐘左右您將得到回復。