- 您現在的位置：買賣IC網 > PDF目錄379646 > ADS-926GM (Electronic Theatre Controls, Inc.) 14-Bit, 500kHz, Low-Power Sampling A/D Converters PDF資料下載
參數資料
| 型號： | ADS-926GM |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 串行ADC |
| 英文描述： | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| 中文描述： | 14位，為500kHz，低功耗采樣A / D轉換器 |
| 文件頁數： | 3/8頁 |
| 文件大小： | 151K |
| 代理商： | ADS-926GM |
ADS -926
3
+25°C
0 to +70°C
–55 to +125°C
ANALOG OUTPUT
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
UNITS
Internal Reference
Voltage
Drift
External Current
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
Volts
ppm/°C
mA
DIGITAL OUTPUTS
Logic Levels
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
Delay, Falling Edge of EOC
to Output Data Valid
Output Coding
+2.4
—
—
—
—
—
—
—
—
+0.4
–4
+4
+2.4
—
—
—
—
—
—
—
—
+0.4
–4
+4
+2.4
—
—
—
—
—
—
—
—
+0.4
–4
+4
Volts
Volts
mA
mA
—
—
35
—
—
35
—
—
35
ns
Offset Binary
POWER REQUIREMENTS, ±15V
Power Supply Ranges
+15V Supply
–15V Supply
+5V Supply
Power Supply Currents
+15V Supply
–15V Supply
+5V Supply
Power Dissipation
Power Supply Rejection
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
Volts
Volts
Volts
—
—
—
—
—
+41
–23
+71
1.4
—
+60
–40
+85
1.75
±0.02
—
—
—
—
—
+41
–23
+71
1.4
—
+60
–40
+85
1.75
±0.02
—
—
—
—
—
+41
–23
+71
1.4
—
+60
–40
+85
1.75
±0.02
mA
mA
mA
Watts
%FSR/%V
POWER REQUIREMENTS, ±12V
Power Supply Ranges
+12V Supply
–12V Supply
+5V Supply
Power Supply Currents
+12V Supply
–12V Supply
+5V Supply
Power Dissipation
Power Supply Rejection
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
Volts
Volts
Volts
—
—
—
—
—
+41
–23
+71
1.3
—
+60
–40
+85
1.6
±0.02
—
—
—
—
—
+41
–23
+71
1.3
—
+60
–40
+85
1.6
±0.02
—
—
—
—
—
+41
–23
+71
1.3
—
+60
–40
+85
1.6
±0.02
mA
mA
mA
Watts
%FSR/%V
TECHNICAL NOTES
1. Obtaining fully specified performance from the ADS-926
requires careful attention to pc-card layout and power
supply decoupling. The device's analog and digital ground
systems are connected to each other internally. For
optimal performance, tie all ground pins (14, 19 and 23)
directly to a large
analog
ground plane beneath the unit.
Bypass all power supplies and the REFERENCE OUTPUT
(pin 21) to ground with 4.7μF tantalum capacitors in parallel
with 0.1μF ceramic capacitors. Locate the bypass capaci-
tors as close to the unit as possible. If the user-installed
offset and gain adjusting circuit shown in Figure 2 is used,
also locate it as close to the ADS-926 as possible.
2. The ADS-926 achieves its specified accuracies without the
need for external calibration. If required, the device's small
initial offset and gain errors can be reduced to zero using
the input circuit of Figure 2. When using this circuit, or any
similar offset and gain-calibration hardware, make adjust-
ments following warmup. To avoid interaction, always adjust
offset before gain.
3. When operating the ADS-926 from ±12V supplies, do not
drive external circuitry with the REFERENCE OUTPUT. The
reference's accuracy and drift specifications may not be
met, and loading the circuit may cause accuracy errors
within the converter.
4. Applying a start convert pulse while a conversion is in
progress (EOC = logic "1") initiates a new and inaccurate
conversion cycle. Data for the interrupted and subsequent
conversions will be invalid.
6.02
(SNR + Distortion) – 1.76 + 20 log
Full Scale Amplitude
Actual Input Amplitude
Effective bits is equal to:
This is the time required before the A/D output data is valid after the analog input
is back within the specified range.
Footnotes:
All power supplies must be on before applying a start convert pulse. All supplies
and the clock (START CONVERT) must be present during warmup periods. The
device must be continuously converting during this time.
See Ordering Information for 0 to +10V input range. Contact DATEL for availability
of other input voltage ranges.
A 500kHz clock with a 200ns wide start convert pulse is used for all production
testing. For applications requiring less than a 500kHz sampling rate, wider start
convert pulses can be used. See Timng Diagramfor more details.
相關PDF資料 |
PDF描述 |
|---|---|
| ADS-926MC | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS-926MM | 14-Bit, 500kHz, Low-Power Sampling A/D Converters |
| ADS-942A | 14-Bit, 2MHz, Low-Power Sampling A/D Converters |
| ADS-942AMC | 14-Bit, 2MHz, Low-Power Sampling A/D Converters |
| ADS-942AME | 14-Bit, 2MHz, Low-Power Sampling A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS-926MC | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 500ksps 14-bit Parallel 24-Pin CDDIP |
| ADS-926MM | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 500ksps 14-bit Parallel 24-Pin CDDIP |
| ADS-927 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:14-Bit, 1MHz, Low-Power Sampling A/D Converters |
| ADS-927/883 | 制造商:Murata Power Solutions 功能描述:ADC Single 2-Step Flash 1Msps 14-bit Parallel 24-Pin DDIP |
| ADS-927GC | 制造商:Murata Power Solutions 功能描述:Single ADC 2-Step Flash 1Msps 14-bit Parallel 24-Pin CDDIP SMD |
發布緊急采購，3分鐘左右您將得到回復。