欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADS-951ME
廠商: Electronic Theatre Controls, Inc.
元件分類: 串行ADC
英文描述: 18-Bit, 1MHz, Low-Power Sampling A/D Converters
中文描述: 18位,1MHz的,低功耗采樣A / D轉換器
文件頁數: 3/6頁
文件大小: 96K
代理商: ADS-951ME
ADS -951
3
+25°C
TYP.
0 to +70°C
TYP.
–40 to +110°C
TYP.
ANALOG OUTPUT
MIN.
MAX.
MIN.
MAX.
MIN.
MAX.
UNITS
Internal Reference
Voltage
Drift
External Current
+4.95
+5.0
±30
1
+5.05
+4.95
+5.0
±30
1
+5.05
+4.95
+5.0
±30
1
+5.05
Volts
ppm/°C
mA
DIGITAL OUTPUTS
Logic Levels
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
Output Coding
+2.4
+0.4
–4
+4
+2.4
+0.4
–4
+4
+2.4
+0.4
–4
+4
Volts
Volts
mA
mA
Complementary Offset Binary
POWER REQUIREMENTS
Power Supply Ranges
+15V Supply
–15V Supply
+5V Supply
–5V Supply
Power Supply Currents
+15V Supply
–15V Supply
+5V Supply
–5V Supply
Power Dissipation
Power Supply Rejection
+14.5
–14.5
+4.75
–4.75
+15.0
–15.0
+5.0
–5.0
+15.5
–15.5
+5.25
–5.25
+14.5
–14.5
+4.75
–4.75
+15.0
–15.0
+5.0
–5.0
+15.5
–15.5
+5.25
–5.25
+14.5
–14.5
+4.75
–4.75
+15.0
–15.0
+5.0
–5.0
+15.5
–15.5
+5.25
–5.25
Volts
Volts
Volts
Volts
+29
–15
+104
–54
1.45
1.65
±0.05
+29
–15
+104
–54
1.45
1.65
±0.05
+29
–15
+104
–54
1.45
1.65
±0.05
mA
mA
mA
mA
Watts
%FSR/%V
THERMAL REQUIREMENTS
All DATEL sampling A/D converters are fully characterized and
specified over operating temperature (case) ranges of 0 to
+70°C and –40 to +110°C. All room-temperature (T
A
= +25°C)
production testing is performed without the use of heat sinks or
forced-air cooling. Thermal impedance figures for each device
are listed in their respective specification tables.
These devices do not normally require heat sinks, however,
standard precautionary design and layout procedures should be
used to ensure devices do not overheat. The ground and power
planes beneath the package, as well as all pcb signal runs to
and from the device, should be as heavy as possible to help
conduct heat away from the package. Electrically-insulating,
thermally-conductive "pads" may be installed underneath the
package. Devices should be soldered to boards rather than
"socketed", and of course, minimal air flow over the surface can
greatly help reduce the package temperature.
TECHNICAL NOTES
1. Obtaining fully specified performance from the ADS-951
requires careful attention to pc-card layout and power
supply decoupling. The device's analog and digital ground
systems are not connected to each other internally. For
optimal performance, tie all ground pins (3, 12 and 13)
directly to a large
analog
ground plane beneath the
package.
Bypass all power supplies and the +5V REFERENCE
OUTPUT (pin 5) to ground with 10μF tantalum capacitors in
parallel with 0.1μF ceramic capacitors. Locate the bypass
capacitors as close to the unit as possible. Tie a 47μF
capacitor between COMPENSATION (pin 7) and ground.
2. The ADS-951 achieves its specified accuracies without the
need for external calibration. If required, the device's small
initial errors can be reduced to zero using the adjustment
circuitry shown in Figure 2. When using this circuitry, or any
similar offset and gain calibration hardware, make adjust-
ments following warmup. To avoid interaction, always adjust
offset before gain. Float pin 6 if not using gain adjust
circuits.
Footnotes:
All power supplies must be on before applying a start convert pulse. All supplies
and the clock (START CONVERT) must be present during warmup periods. The
device must be continuously converting during this time.
Contact DATEL for other input voltage ranges.
This is the time required before the A/D output data is valid once the analog input
is back within the specified range.
6.02
(SNR + Distortion) – 1.76 + 20 log
Full Scale Amplitude
Actual Input Amplitude
A 1MHz clock with a 500nsec positive pulse width (50% duty cycle) is used for
all production testing. Any duty cycle may be used as long as a minimum
positive pulse width of 20nsec is maintained. For applications requiring lower
sampling rates, clock frequencies lower than 1MHz may be used.
Effective bits is equal to:
3. Applying a start convert pulse while a conversion is in
progress (EOC = logic "1") will initiate a new and probably
inaccurate conversion cycle. Data for the interrupted and
subsequent conversions will be invalid.
相關PDF資料
PDF描述
ADS-953 18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS-953MC 18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS-953ME 18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS953 18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS-B932 16-Bit, 2MHz Sampling A/D Converters
相關代理商/技術參數
參數描述
ADS953 制造商:未知廠家 制造商全稱:未知廠家 功能描述:18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS-953 制造商:未知廠家 制造商全稱:未知廠家 功能描述:18-Bit, 1MHz, Low-Distortion Sampling A/D Converters
ADS-953MC 制造商:Murata Power Solutions 功能描述:Dual ADC 2-Step Flash 1Msps 18-bit Parallel 32-Pin TDIP
ADS-953ME 制造商:Murata Power Solutions 功能描述:Dual ADC 2-Step Flash 1Msps 18-bit Parallel 32-Pin TDIP
ADS976 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter IC
主站蜘蛛池模板: 靖西县| 皋兰县| 保山市| 抚州市| 遵化市| 新绛县| 宁安市| 德惠市| 察哈| 青海省| 盐池县| 洛宁县| 安新县| 年辖:市辖区| 星座| 文水县| 来凤县| 壶关县| 聊城市| 静海县| 诸城市| 蓬溪县| 汾西县| 潜山县| 义马市| 嘉黎县| 和政县| 酒泉市| 天津市| 晋江市| 长丰县| 博兴县| 新河县| 葫芦岛市| 华安县| 澄城县| 门源| 新田县| 德兴市| 河东区| 祁门县|