- 您現在的位置：買賣IC網 > PDF目錄374037 > ADSP-21XX1111 (Analog Devices, Inc.) ADSP-2100 Family DSP Microcomputers PDF資料下載
參數資料
| 型號： | ADSP-21XX1111 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | ADSP-2100 Family DSP Microcomputers |
| 中文描述： | 的ADSP - 2100系列DSP的微機 |
| 文件頁數： | 7/32頁 |
| 文件大小： | 231K |
| 代理商： | ADSP-21XX1111 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADSP-21mod870
–7–
REV. 0
ratio. The default form of the instruction, when no clock divisor
is given, is the standard IDLE instruction.
When the IDLE (
n
) instruction is used, it effectively slows down
the processor’s internal clock and thus its response time to in-
coming interrupts. The one-cycle response time of the standard
idle state is increased by n, the clock divisor. When an enabled
interrupt is received, the ADSP-21mod870 will remain in the idle
state for up to a maximum of
n
processor cycles (
n
= 16, 32, 64,
or 128) before resuming normal operation.
When the IDLE (
n
) instruction is used in systems that have an
externally generated serial clock (SCLK), the serial clock rate
may be faster than the processor’s reduced internal clock rate.
Under these conditions, interrupts must not be generated at a
faster rate than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of
n
processor cycles).
SYSTEM INTERFACE
Figure 3 shows a typical multichannel modem configuration
with the ADSP-21mod870. A line interface can be used to
connect the multichannel subscriber or client data stream to the
multichannel serial port of the ADSP-21mod870. The ADSP-
21mod870 can support 24 or 32 channels. The IDMA port of
the ADSP-21mod870 is used to give a host processor full access
to the internal memory of the ADSP-21mod870. This lets the
host dynamically configure the ADSP-21mod870 by loading code
and data into its internal memory. This configuration also lets
the host access server data directly from the ADSP-21mod870’s
internal memory. In this configuration, the ADSP-21mod870
should be put into host memory mode where Mode C = 1,
Mode B = 0 and Mode A = 1 (see Table II).
CLOCK SIGNALS
The ADSP-21mod870 can be clocked by either a crystal or a
TTL-compatible clock signal.
The CLKIN input cannot be halted, changed during operation,
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual,
Third Edition,
for detailed
information on this power-down feature.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-21mod870 uses an input clock with a frequency
equal to half the instruction rate; a 26 MHz input clock yields a
19 ns processor cycle (which is equivalent to 52 MHz). Nor-
mally, instructions are executed in a single processor cycle. All
device timing is relative to the internal instruction clock rate,
which is indicated by the CLKOUT signal when enabled.
Because the ADSP-21mod870 includes an on-chip oscillator
circuit, an external crystal may be used. The crystal should be
connected across the CLKIN and XTAL pins, with two capaci-
tors connected as shown in Figure 4. Capacitor values are de-
pendent on crystal type and should be specified by the crystal
manufacturer. A parallel-resonant, fundamental frequency,
microprocessor-grade crystal should be used.
A clock output (CLKOUT) signal is generated by the processor
at the processor’s cycle rate. This is enabled and disabled by the
CLKODIS bit in the SPORT0 Autobuffer Control Register.
ADSP-
21mod870
IDMA
SP0
ADSP-
21mod870
SP0
IDMA
ADSP-
21mod870
IDMA
SP0
ADSP-
21mod870
SP0
IDMA
ADSP-
21mod870
IDMA
SP0
ADSP-
21mod870
SP0
IDMA
ADSP-
21mod870
IDMA
SP0
ADSP-
21mod870
SP0
IDMA
LINE
INTERFACE
CALL
CONTROL
T1, E1, PRI,
xDSL, ATM
HOST BUS
HOST
(2183)
LAN OR
INTERNET
ADSP-21mod870 FUNCTIONS
HOST FUNCTIONS
MULTI-DSP CONTROL AND OVERLAY
MANAGEMENT
SERVICE 32 DSPs/HOST
DATA PACKETIZING
V.34/56k MODEM
V.17 FAX
V.42, V.42bis, MNP2-5
DTMF DIALING
CALLER ID
HDLC PROTOCOL
Figure 3. Network Access System
CLKIN
CLKOUT
XTAL
DSP
Figure 4. External Crystal Connections
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21XX4444 | ADSP-2100 Family DSP Microcomputers |
| ADSP-21MSP5859 | LM101A/LM201A/LM301A Operational Amplifiers; Package: MDIP; No of Pins: 8; Qty per Container: 40; Container: Rail |
| ADSP-21XX | ADSP-2100 Family DSP Microcomputers |
| ADSP-21MOD970-110 | Multiport Internet Gateway Processor Solution |
| ADSP-21mod970-110 | Data Pump Solution Gateway Processor Solution(多端口網關處理器解決方案) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-3128AJG | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| ADSP-3128ASG/883B | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-3201JG | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| ADSP-3201KG | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:MULTIPLIER, 144 Pin, Ceramic, PGA |
| ADSP-3201TG | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。