- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7466 (Analog Devices, Inc.) dBCool Remote Thermal Controller and Voltage Monitor PDF資料下載
參數資料
| 型號： | ADT7466 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | dBCool Remote Thermal Controller and Voltage Monitor |
| 中文描述： | dBCool遠程熱控制器和電壓監視器 |
| 文件頁數： | 30/48頁 |
| 文件大小： | 1269K |
| 代理商： | ADT7466 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADT7466
AFC Loop Operation
The automatic fan speed control loop operates as follows.
Rev. 0 | Page 30 of 48
STARTING THE FAN
Under normal conditions, the V_FAN_ON register sets DRIVE
at a voltage sufficient to start the fan rotating. Fan startup is
confirmed after two tach pulses are generated.
Once the temperature exceeds T_MIN, the ADT7466 outputs
the voltage V_FAN_ON on its DRIVE pin. For Fan 1, FAN1 ON
is also asserted. When the fan starts rotating reliably, the drive
voltage is reduced to V_FAN_MIN. Reliable startup is
determined when two tachometer pulses are sensed on the tach
input. As the measured temperature increases, the voltage
output by the ADT7466 also increases linearly. The rate with
which the voltage output (fan speed) increases is controlled by
the T_RANGE parameter.
1.
Set the initial V_FAN_ON by BIOS.
2.
Wait for two tach pulses (up to 2 seconds maximum).
3.
If successful, set the drive to V_FAN_MIN and follow the
automatic slope.
If not successful, increase the V_FAN_ON voltage on
DRIVE by a programmed value (set in step size register)
and return to Step 1. This sequence can be repeated five
times or until DRIVE is set at full scale. If the fan still fails
to start, the FANLOCK pin is asserted.
Once the measured fan speed reaches a programmable
maximum limit, the fan speed does not increase further. This is
to maintain low acoustics. If, however, the THERM fail safe
limit is breached, the fans immediately run to full speed (0xFF).
They continue to run at full speed until the temperature falls by
a programmable hysteresis value below the THERM limit. Then
the fan speed reduces to its value before the THERM limit is
exceeded.
4.
5.
Set the drive at 0 V (to avoid high power dissipation).
Wait 1 minute and repeat the entire sequence. (This
sequence recovers the situation if the fan is temporarily
stalled due a mechanical reason such as jammed with a
stick.)
As the temperature decreases, the fan speed decreases along the
same curve. Once the temperature falls below T_MIN, the fan
runs at V_FAN_MIN. If the temperature continues to decrease,
the fan can continue to run at V_FAN_MIN, or if the
temperature drops below a hysteresis value, the fan can be
switched off completely. This is controlled by Bits 4:5 of
Configuration Register 4. Setting these bits ensures that the fans
never go below minimum speed. FAN 1 ON is also deasserted
when the fan drive is set to 0 V.
0
FULL SPEED
2.25V
(0xFF)
FAN DRIVE V
TMIN
TACHO
V_FAN_ON
V_FAN_MIN
FAN OFF
0V
(0x00)
The fan speed is updated every 250 ms to 500 ms in the
automatic fan speed control loop.
0
FULL S2.25V
(0xFF)
FAN DRIVE V
MAX FAN
SPEED
FAN SPIN UP
FPULSES
TEMPERATURE
T_THERM
TMIN
TMIN_HYS
TRANGE
TMAX
V_FAN_ON
V_FAN_MIN
FAN OFF
0V
(0x00)
T_THERM_HYS
Figure 42. Normal Fan Starting Timing Diagram
0
FULL SPEED
(2.25V
FAN DRIVE V
FAN1_ON
FAN_LOCK
V_FAN_ON
V_FAN_ON_STEP
V_FAN_MIN
FAN OFF
0V
(0x00)
2SEC
1MIN
Figure 41. Operation of AFC Loop
Figure 43. Abnormal Fan Starting (Fan Stalled)
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7466ARQZ | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL7 | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7516 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7466ARQZ | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7466ARQZ-RL7 | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ZEVB | 功能描述:BOARD EVALUATION ADT7466 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。