- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7466ARQZ-REEL7 (ANALOG DEVICES INC) dBCool Remote Thermal Controller and Voltage Monitor PDF資料下載
參數資料
| 型號： | ADT7466ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | dBCool Remote Thermal Controller and Voltage Monitor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 23/48頁 |
| 文件大小： | 1269K |
| 代理商： | ADT7466ARQZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADT7466
ALERT INTERRUPT BEHAVIOR
The ADT7466 can be polled for status, or an ALERT interrupt
can be generated for out-of-limit conditions. It is important to
note how the ALERT output and status bits behave when
writing interrupt handler software.
Rev. 0 | Page 23 of 48
0
HIGH LIMIT
TEMPERATURE
STICKY
STATUS
BIT
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
CLEARED ON READ
(TEMP BELOW LIMIT)
ALERT
Figure 28. ALERT and Status Bit Behavior
Figure 28 shows how the ALERT output and sticky status bits
behave. Once a limit is exceeded, the corresponding status bit is
set to 1. The status bit remains set until the error condition
subsides and the status register is read. This ensures that an out-
of-limit event cannot be missed if software is polling the device
periodically. The ALERT output remains low while a reading is
out-of-limit, until the status register is read. This has implica-
tions on how software handles the interrupt.
Handling Alert Interrupts
To prevent the system from being tied up servicing interrupts, it
is recommended to handle the ALERT interrupt as follows:
1.
Detect the ALERT assertion.
2.
Enter the interrupt handler.
3.
Read the status registers to identify the interrupt source.
4.
Mask the interrupt source by setting the appropriate mask
bit in the interrupt mask registers (0x12, 0x13).
5.
Take the appropriate action for a given interrupt source.
6.
Exit the interrupt handler.
7.
Periodically poll the status registers. If the interrupt status
bit has cleared, reset the corresponding interrupt mask bit
to 0. This causes the ALERT output and status bits to
behave as shown in Figure 29.
0
HIGH LIMIT
TEMPERATURE
STICKY
STATUS
BIT
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
INTERRUPT
MASK BIT SET
ALERT
CLEARED ON READ
(TEMP BELOW LIMIT)
INTERRUPT MASK BIT
CLEARED
(ALERT REARMED)
Figure 29. How Masking the Interrupt Source Affects ALERT Output
Masking Interrupt Sources
Interrupt Mask Registers 1 and 2 are located at Addresses 0x12
and 0x13. These registers allow individual interrupt sources to
be masked to prevent ALERT interrupts. Masking an interrupt
source prevents only the ALERT output from being asserted;
the appropriate status bit is set as normal.
Table 22. Interrupt Mask Register 1 (Reg. 0x12)
Bit No.
Name
Description
7
OOL
1 masks ALERT for any alert condition
flagged in Status Register 2.
6
AIN1(TH1)/
REM2
5
AIN2(TH2)
1 masks ALERT for AIN2(TH2).
4
VCC
1 masks ALERT for Vcc.
3
REM1
1 masks ALERT for remote
temperature.
2
LOC
1 masks ALERT for local temperature.
1
FAN1
1 masks ALERT for Fan 1.
0
FAN2
1 masks ALERT for Fan 2.
Table 23. Interrupt Mask Register 2 (Reg. 0x13)
Bit No.
Name
Description
5
THRM2 1 masks ALERT for TH1 open- or short-circuit
errors.
4
THRM1 1 masks TH2 open- or short-circuit errors.
3
D1
1 masks ALERT for Diode 1 open- or short-
circuit errors.
2
D2
1 masks ALERT for Diode 2 open- or short-
circuit errors.
1
PHOT
1 masks ALERT for PROCHOT.
0
OVT
1 masks ALERT for over temperature
(exceeding THERM limits).
1 masks ALERT for AIN1(TH1)/REM2.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7516 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1-REEL | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1-REEL7 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7516ARQ | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7466ARQZ-RL7 | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ZEVB | 功能描述:BOARD EVALUATION ADT7466 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADT7467 | 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCool Remote Thermal Monitor and Fan Controller |
| ADT7467ARQ | 功能描述:IC PWM FAN CTRLR W/MONITR 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7467ARQ-REEL | 功能描述:IC REMOTE THERMAL CTRLR 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。