- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7466ARQZ-REEL (ANALOG DEVICES INC) dBCool Remote Thermal Controller and Voltage Monitor PDF資料下載
參數資料
| 型號： | ADT7466ARQZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | dBCool Remote Thermal Controller and Voltage Monitor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | LEAD FREE, MO-137AB, QSOP-16 |
| 文件頁數： | 15/48頁 |
| 文件大小： | 1269K |
| 代理商： | ADT7466ARQZ-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADT7466
ALERT RESPONSE ADDRESS (ARA)
ARA is a feature of SMBus devices that allows an interrupting
device to identify itself to the host when multiple devices exist
on the same bus. The ALERT output can be used as an interrupt
output, or it can be used as an ALERT. One or more outputs can
be connected to a common ALERT line connected to the
master. If a device’s ALERT line goes low, the following occurs:
1.
ALERT is pulled low.
2.
The master initiates a read operation and sends the alert
response address (ARA = 0001 100). This is a general call
address, which must not be used as a specific device
address.
3.
The device whose ALERT output is low responds to the
alert response address, and the master reads its device
address. The address of the device is now known, and it
can be interrogated in the usual way.
4.
If more than one device’s ALERT output is low, the one
with the lowest device address has priority, in accordance
with normal SMBus arbitration.
5.
Once the ADT7466 responds to the alert response address,
the master must read the status registers, the ALERT is
cleared only if the error condition no longer exists.
Rev. 0 | Page 15 of 48
SMBus TIMEOUT
The ADT7466 includes an SMBus timeout feature. If there is no
SMBus activity for 25 ms, the ADT7466 assumes that the bus is
locked, and it releases the bus. This prevents the device from
locking or holding the SMBus expecting data. Some SMBus
controllers cannot handle the SMBus timeout feature, so they
are disabled.
Table 5. Configuration Register 1—Register 0x00
Bit Address and Value
Description
<5> TODIS = 0
SMBus timeout enabled (default)
<5> TODIS = 1
SMBus timeout disabled
VOLTAGE MEASUREMENT
The ADT7466 has two external voltage measurement channels.
Pin 11 and Pin 12 are analog inputs with a range of 0 V to
2.25 V. It can also measure its own supply voltage, V
CC
. The V
CC
supply voltage measurement is carried out through the V
CC
pin
(Pin 6). Setting Bit 6 of Configuration Register 1 (0x00) allows a
5 V supply to power the ADT7466 and be measured without
overranging the V
CC
measurement channel.
A/D Converter
All analog inputs are multiplexed into the on-chip, successive
approximation, analog-to-digital converter. This has a resolution
of 10 bits. The basic input range is 0 V to 2.25 V, but the V
CC
input has built in attenuators to allow measurement of 3.3 V or
5 V. To allow for the tolerance of the supply voltage, the ADC
produces an output of 3/4 full scale (decimal 768 or 0x300) for
the nominal supply voltage, and so has adequate headroom to
cope with overvoltages.
Table 9 shows the input ranges of the analog inputs and the
output codes of the ADC.
Table 6. Voltage Measurement Registers
Register
Description
0x0A
AIN1 reading
0x0B
AIN2 reading
0x0C
V
CC
reading
Associated with each voltage measurement channel are high
and low limit registers. Exceeding the programmed high or low
limit causes the appropriate status bit to be set. Exceeding either
limit can also generate ALERT interrupts.
Default
0x00
0x00
0x00
Table 7. Voltage Measurement Limit Registers
Register
Description
0x14
AIN1 low limit
0x15
AIN1 high limit
0x16
AIN2 low limit
0x17
AIN2 high limit
0x18
V
CC
low limit
0x19
V
CC
high limit
When the ADC is running, it samples and converts a voltage
input in 1 ms, and averages 16 conversions to reduce noise.
Therefore a measurement on each input takes nominally 16 ms.
Default
0x00
0xFF
0x00
0xFF
0x00
0xFF
Turn Off Averaging
For each voltage measurement read from a value register, 16
readings have actually been made internally and the results
averaged, before being placed into the value register. There can
be an instance where faster conversions are required. Setting
Bit 4 of Configuration Register 2 (0x01) turns averaging off.
This effectively gives a reading 16 times faster (1 ms), but as a
result the reading can be noisier.
Single-Channel ADC Conversions
Setting Bit 3 of Configuration Register 4 (0x03) places the
ADT7466 into single-channel ADC conversion mode. In this
mode, the ADT7466 can be made to read a single voltage channel
only. If the internal ADT7466 clock is used, the selected input is
read every 1 ms. The appropriate ADC channel is selected by
writing to Bits 2:0 of Configuration Register 4 (0x03).
Table 8. Single-Channel ADC Conversions
Bits 2:0, Reg. 0x03
000
001
010
Channel Selected
AIN1
AIN2
V
CC
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7466ARQZ-REEL7 | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7516 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1-REEL | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1-REEL7 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7466ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7466ARQZ-RL7 | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ZEVB | 功能描述:BOARD EVALUATION ADT7466 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADT7467 | 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCool Remote Thermal Monitor and Fan Controller |
| ADT7467ARQ | 功能描述:IC PWM FAN CTRLR W/MONITR 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。