欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： ADUC848BS32-5
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
中文描述： 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52
封裝： 14 X 14 MM, PLASTIC, MO-112-AC-1, MQFP-52
文件頁數： 35/108頁
文件大小： 1109K
代理商： ADUC848BS32-5
ADuC845/ADuC847/ADuC848
subtracts the offset calibration error, it is advisable to perform
an offset calibration at the same gain range as that used for full-
scale calibration. There is no penalty to the full-scale calibration
in redoing the zero-scale calibration at the required PGA range
because the full-scale calibration has very good matching at all
the PGA ranges.
Rev. A | Page 35 of 108
This procedure also applies when chop is disabled.
Note that for internal calibration to be effective, the AIN
pin
should be held at a steady voltage, within the allowable common-
mode range to keep it from floating during calibration.
System Calibration Example
With chop enabled, a system zero-scale or offset calibration
should never be required. However, if a full-scale or gain
calibration is required for any reason, use the following typical
procedure for doing so.
1.
Apply a differential voltage of 0 V to the selected analog
inputs (AIN+ to AIN) that are held at a common-mode
voltage.
Perform a system zero-scale or offset calibration by setting
the MD2...0 bits in the ADCMODE register to 110B.
2.
Apply a full-scale differential voltage across the ADC
inputs again at the same common-mode voltage.
Perform a system full-scale or gain calibration by setting
the MD2...0 bits in the ADCMODE register to 111B.
Perform a system calibration at the required PGA range to be
used since the ADC scales to the differential voltages that are
applied to the ADC during the calibration routines.
In bipolar mode, the zero-scale calibration determines the mid-
scale point of the ADC (800000H) or 0 V.
PROGRAMMABLE GAIN AMPLIFIER
The primary ADC incorporates an on-chip programmable gain
amplifier (PGA). The PGA can be programmed through eight
different ranges, which are programmed via the range bits (RN0
to RN2) in the ADC0CON1 register. With an external 2.5 V
reference applied, the unipolar ranges are 0 mV to 20 mV, 0 mV
to 40 mV, 0 mV to 80 mV, 0 mV to 160 mV, 0 mV to 320 mV,
0 mV to 640 mV, 0 V to 1.28 V and 0 V to 2.56 V, while in
bipolar mode the ranges are ±20 mV, ±40 mV, ±80 mV, ±160 mV,
±320 mV, ±64 0 mV, ±1.28 V, and ±2.56 V. These ranges should
appear on the input to the on-chip PGA. The ADC range-
matching specification of 2 μV (typical with chop enabled)
means that calibration need only be carried out on a single
range and need not be repeated when the ADC range is
changed. This is a significant advantage compared to similar
mixed-signal solutions available on the market. The auxiliary
(ADuC845 only) ADC does not incorporate a PGA, and the
gain is fixed at 0 V to 2.50 V in unipolar mode, and ±2.50 V in
bipolar mode.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog inputs of the ADuC845/ADuC847/ADuC848 can
accept either unipolar or bipolar input voltage ranges. Bipolar
input ranges do not imply that the part can handle negative
voltages with respect to system AGND, but rather with respect
to the negative reference input. Unipolar and bipolar signals on
the AIN(+) input on the ADC are referenced to the voltage on
the respective AIN() input. AIN(+) and AIN() refer to the
signals seen by the ADC.
For example, if AIN() is biased to 2.5 V (tied to the external
reference voltage) and the ADC is configured for a unipolar
analog input range of 0 mV to > 20 mV, the input voltage range
on AIN(+) is 2.5 V to 2.52 V. On the other hand, if AIN(
)
is
biased to 2.5 V (again the external reference voltage) and the
ADC is configured for a bipolar analog input range of ±1.28 V,
the analog input range on the AIN(+) is 1.22 V to 3.78 V, that is,
2.5 V ± 1.28 V.
The modes of operation for the ADC are fully differential mode
or pseudo differential mode. In fully differential mode, AIN1 to
AIN2 are one differential pair, AIN3 to AIN4 are another pair
(AIN5 to AIN6, AIN7 to AIN8, and AIN9 to AIN10 are the
others). In differential mode, all AIN(
)
pin names imply the
negative analog input of the selected differential pair, that is,
AIN2, AIN4, AIN6, AIN8, AIN10. The term AIN(+) implies the
positive input of the selected differential pair, that is, AIN1,
AIN3, AIN5, AIN7, AIN9. In pseudo differential mode, each
analog input is paired with the AINCOM pin, which can be
biased up or tied to AGND. In this mode, the AIN(
)
implies
AINCOM and AIN(+) implies any one of the ten analog input
channels.
The configuration of the inputs (unipolar versus bipolar) is
shown in Figure 17.
AIN1
I
A
C
A
C
I
I
I
I
I
I
I
I
I
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
AINCOM
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
FULLY DIFFERENTIAL
FULLY DIFFERENTIAL
FULLY DIFFERENTIAL
FULLY DIFFERENTIAL
FULLY DIFFERENTIAL
AINCOM
0
Figure 17. Unipolar and Bipolar Channel Pairs
相關PDF資料
PDF描述
ADUC848BS62-3 10-825944-010
ADUC848BS62-5 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC848BS8-3 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC848BS8-5 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC845 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
相關代理商/技術參數
參數描述
ADUC848BS62-3 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.85MHZ 3.3V 52MQFP - Bulk 制造商:Analog Devices 功能描述:
ADUC848BS62-5 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.85MHZ 5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:IC MICROCONTROLLER
ADUC848BS8-3 制造商:Analog Devices 功能描述:
ADUC848BS8-5 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:IC MICROCONTROLLER
ADUC848BSZ32-3 功能描述:IC MCU FLASH W/16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 瓦房店市| 赣榆县| 梁河县| 洞口县| 黑河市| 和林格尔县| 涞源县| 府谷县| 修武县| 汾阳市| 合水县| 淮南市| 嘉义县| 怀远县| 尼木县| 高平市| 延津县| 东乌珠穆沁旗| 句容市| 辰溪县| 延安市| 西丰县| 闸北区| 信阳市| 洛阳市| 平乐县| 沅陵县| 宁夏| 房产| 门源| 浪卡子县| 江口县| 绥江县| 绵阳市| 乐陵市| 黑山县| 韶关市| 洛川县| 嘉定区| 蒙山县| 镇安县|