- 您現在的位置：買賣IC網 > PDF目錄374042 > ADuM1311BRWZ1 (Analog Devices, Inc.) Triple-Channel Digital Isolators PDF資料下載
參數資料
| 型號： | ADuM1311BRWZ1 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Triple-Channel Digital Isolators |
| 中文描述： | 三通道數字隔離器 |
| 文件頁數： | 18/20頁 |
| 文件大?。?/td> | 282K |
| 代理商： | ADUM1311BRWZ1 |
ADuM1310/ADuM1311
APPLICATION INFORMATION
PC BOARD LAYOUT
The ADuM131x digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins (see
Figure 13). Bypass capacitors are most conveniently connected
between Pin 1 and Pin 2 for V
DD1
and between Pin 15 and Pin 16
for V
DD2
. The capacitor value should be between 0.01 μF and
0.1 μF. The total lead length between both ends of the capacitor
and the input power supply pin should not exceed 20 mm.
Bypassing between Pin 1 and Pin 8 and between Pin 9 and
Pin 16 should be considered, unless both of the ground pins on
each package are connected together close to the package.
Rev. F | Page 18 of 20
0
GND
1
V
DD1
GND
2
V
DD2
GND1
V
IA
GND
2
V
OA
V
IB
V
OB
V
IC
/V
OC
V
OC
/V
IC
NC
NC
CTRL
1
CTRL
2
Figure 13. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, care
should be taken to ensure that board coupling across the isolation
barrier is minimized. Furthermore, the board layout should be
designed such that any coupling that does occur equally affects
all pins on a given component side. Failure to ensure this can
cause voltage differentials between pins exceeding the device’s
absolute maximum ratings, thereby leading to latch-up or
permanent damage.
PROPAGATION DELAY
RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The input-to-
output propagation delay time for a high-to-low transition may
differ from the propagation delay time of a low-to-high transition.
0
INPUT (V
Ix
)
OUTPUT (V
Ox
)
t
PLH
t
PHL
50%
50%
Figure 14. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM131x component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM131x
components operating under the same conditions.
DC CORRECTNESS AND MAGNETIC FIELD
IMMUNITY
Positive and negative logic transitions at the isolator input
cause narrow (~1 ns) pulses to be sent to the decoder via the
transformer. The decoder is bistable and is therefore either set
or reset by the pulses, indicating input logic transitions. In the
absence of logic transitions at the input for more than 2 μs, a
periodic set of refresh pulses indicative of the correct input state
are sent to ensure dc correctness at the output. If the decoder
receives no internal pulses of more than about 5 μs, the input
side is assumed to be unpowered or nonfunctional, in which
case the isolator output is forced to a default state (see Table 12)
by the watchdog timer circuit.
The magnetic field immunity of the ADuM131x is determined
by the changing magnetic field, which induces a voltage in the
transformer’s receiving coil large enough to either falsely set or
reset the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of the
ADuM131x is examined because it represents the most suscep-
tible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V The decoder has a sensing threshold at about 0.5 V thus
establishing a 0.5 V margin in which induced voltages can be
tolerated. The voltage induced across the receiving coil is given by
V
= (
d
β
/dt
)
∑
π
r
n2
; n
= 1, 2, … ,
N
where:
β is magnetic flux density (gauss).
N
is the number of turns in the receiving coil.
r
n
is the radius of the n
th
turn in the receiving coil (cm).
Given the geometry of the receiving coil in the ADuM131x and
an imposed requirement that the induced voltage be, at most,
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field at a given frequency can be calculated. The result
is shown in Figure 15.
相關PDF資料 |
PDF描述 |
|---|---|
| ADuM1311BRWZ-RL1 | Triple-Channel Digital Isolators |
| ADUM1400 | Quad-Channel Digital Isolators |
| ADUM1400ARW | Quad-Channel Digital Isolators |
| ADUM1400ARWZ | Quad-Channel Digital Isolators |
| ADUM1400BRW | Quad-Channel Digital Isolators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUM1311BRWZ-RL | 功能描述:IC ISOLATOR DGTL 3CHAN 16-SOIC RoHS:是 類別:隔離器 >> 數字隔離器 系列:iCoupler® 產品培訓模塊:IsoLoop® Isolator 標準包裝:50 系列:IsoLoop® 輸入 - 1 側/2 側:5/0 通道數:5 電源電壓:3 V ~ 5.5 V 電壓 - 隔離:2500Vrms 數據速率:110Mbps 傳輸延遲:12ns 輸出類型:CMOS 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 工作溫度:-40°C ~ 85°C 其它名稱:390-1053-5 |
| ADUM1311BRWZ-RL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Triple-Channel Digital Isolators |
| ADUM131D0BRWZ | 功能描述:General Purpose Digital Isolator 3750Vrms 3 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:管件 零件狀態:有效 技術:磁耦合 類型:通用 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:3750Vrms 共模瞬態抗擾度（最小值）:75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL（最大值）:13ns，13ns 脈寬失真（最大）:3ns 上升/下降時間（典型值）:2.5ns，2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:16-SOIC 標準包裝:47 |
| ADUM131D0BRWZ-RL | 功能描述:General Purpose Digital Isolator 3750Vrms 3 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:帶卷（TR） 零件狀態:有效 技術:磁耦合 類型:通用 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:3750Vrms 共模瞬態抗擾度（最小值）:75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL（最大值）:13ns，13ns 脈寬失真（最大）:3ns 上升/下降時間（典型值）:2.5ns，2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:16-SOIC 標準包裝:1,000 |
| ADUM131D0BRZ | 功能描述:General Purpose Digital Isolator 3000Vrms 3 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.154", 3.90mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:管件 零件狀態:有效 技術:磁耦合 類型:通用 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:3000Vrms 共模瞬態抗擾度（最小值）:75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL（最大值）:13ns，13ns 脈寬失真（最大）:3ns 上升/下降時間（典型值）:2.5ns，2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:16-SOIC 標準包裝:48 |
發布緊急采購，3分鐘左右您將得到回復。