- 您現在的位置：買賣IC網 > PDF目錄379658 > AG1160-48 (Electronic Theatre Controls, Inc.) 5V RINGING SLIC PDF資料下載
參數資料
| 型號： | AG1160-48 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 5V RINGING SLIC |
| 中文描述： | 5V的振鈴用戶接口 |
| 文件頁數： | 5/12頁 |
| 文件大小： | 161K |
| 代理商： | AG1160-48 |
V1.8 October 2006
Data Sheet
Codecs require information about the transfer
characteristics of the SLIC with which they are working.
Some codecs require a .CIR netlist. A .CIR netlist can
be obtained by contacting either Silver Telecom or your
local
representative,
to
programming coefficients to be generated.
If a simple (non-programmable) Codec is being used
contact Silver Telecom for an Ag1160 version with an
alternative impedance.
2.3 Network Balance Impedance.
The network balance impedance, Zb, of the SLIC is set
to 600R for the standard Ag1160. For countries where
the network balance impedance is 600R e.g. North
America, no external adjustment is required. For
countries where an alternative network balance
impedance is used the Codec filter characteristics can
be programmed to give the required matching. The
.CIR netlist may be needed to allow the Codec
programming coefficients to be generated.
Ag1160
5V RINGING SLIC
Silver Telecom 2006
Page 5
allow
certain
Codec
If a simple (non-programmable) Codec is being used
contact Silver Telecom for an Ag1160 version with an
alternative impedance.
2.4 Tip & Ring Polarity Reversal.
The Ag1160 can reverse the battery voltage polarity at
Tip and Ring via the F/R pin.
If F/R is held at logic 1 (forward) the d.c. voltage at Tip
is positive with respect to Ring. If F/R is taken to logic
0 the voltage polarity is reversed. The F/R pin should
not be left floating, and if not used should be tied high
as shown in Figure 4.
2.5 On Hook Transmission.
The Ag1160 is capable of on-hook transmission. This
means analog signals can be transmitted from V
IN
through Tip and Ring and onto the line even when no
loop current is flowing. This can be used when
Condition 1 - DC operation
Signal
Notes
INPUT RM
1
0
No ringing
OUTPUT SHK
1
0
Off hook detected
Off Hook
NOTE: SHK SHOULD
BE DE-BOUNCED
Condition 2 - Ringing On-hook
RM
1
0
F/R
(input)
1
0
SHK
1
0
Condition 3 - Ringing/Off-hook
A
B
The phone goes off hook, and SHK is detected at point A
(leading edge). RM must be switched low in <500ms
(point B), and the ringing cadence should be removed
from F/R..
As long as the telephone is off hook, SHK will remain high.
1 sec
3 sec
1 sec
3 sec
Figure 3: Ringing Signal Waveforms
相關PDF資料 |
PDF描述 |
|---|---|
| AG1160A | 5V RINGING SLIC |
| AG1160A-48 | 5V RINGING SLIC |
| AG1170 | +5V / +3.3V Low Power Ringing SLIC |
| AG1170-D3 | +5V / +3.3V Low Power Ringing SLIC |
| AG1170-D5 | +5V / +3.3V Low Power Ringing SLIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AG1160A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V RINGING SLIC |
| AG1160A-48 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V RINGING SLIC |
| AG11692 | 制造商:Molex 功能描述:LOCKNUT PG9 *52003500* |
| AG1170 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:+5V / +3.3V Low Power Ringing SLIC |
| AG1170-D3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:+5V / +3.3V Low Power Ringing SLIC |
發布緊急采購，3分鐘左右您將得到回復。