- 您現在的位置：買賣IC網 > PDF目錄379659 > AG1460PS (Electronic Theatre Controls, Inc.) QUAD 5V RINGING SLIC PDF資料下載
參數資料
| 型號： | AG1460PS |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | QUAD 5V RINGING SLIC |
| 中文描述： | 四5V的振鈴用戶接口 |
| 文件頁數： | 5/15頁 |
| 文件大小： | 264K |
| 代理商： | AG1460PS |
V1.4 May 2004
Data Sheet
1.2 DIL Format Pin Out
Pin #
Ag1460
QUAD 5V RINGING SLIC
Name
Description
1, 28, 29, 56
RM
Ringing Mode.
Sets bias conditions during ringing. Must be set
to logic 1 during ringing. Must be set to logic 0 within 500ms of
Ring Trip detect and during normal Off Hook condition.
Audio Out.
This is the analog output signal (from Tip and Ring)
to the Codec. Must be ac coupled with typically 100nF.
Balance Impedance.
Connect programming components
between ZB and V
IN
on Ag1460P only.*
Analog Supply.
Each pin must be connected to +5V
PWR
with
10
resistors. Decouple each with 100uF (16V) capacitors.
Switch Hook.
Indicates Off-Hook when at logic 1. Must be
de-bounced
Terminal Impedance 1.
Connect programming components
between ZT
1
and ZT
2
on Ag1460P only.*
Terminal Impedance 2.
Connect programming components
between ZT
1
and ZT
2
on Ag1460P only.*
Audio In.
This is the analog input signal from the Codec (which is
output on Tip and Ring). Must be ac coupled with typically
100nF.
Forward/Reverse.
A logic 0 will reverse the Tip and Ring voltage
polarities. F/R is toggled to produce the ringing output.
Slew Rate Capacitor.
A capacitor is fitted between this pin and
GND to control the battery reversal and the ringing slew rate.
220nF is recommended.
Loop Off.
A logic 1 removes the loop current from the line.
Connect to logic 0 for normal operation.
2, 27, 30, 55
V
OUT
3, 26, 31, 54
ZB*
4, 25, 32, 53
+5V
A
5, 24, 33, 52
SHK
6, 23, 34, 51
ZT
1
*
7, 22, 35, 50
ZT
2
*
8, 21, 36, 49
V
IN
9, 20, 37, 48
F/R
10, 19, 38, 47
CAP
11, 18, 39, 46
LO
12, 17, 40, 45
TIP (A)
Tip.
Connects to the subscriber line Tip.
13, 16, 41, 44 RING (B)
Ring.
Connects to the subscriber line Ring.
14
+5V
PWR
DC-DC Supply.
+5V input for the integral DC-DC converter.
Decouple to GNDPWR with 220uF (10V) low impedance
capacitor.
15
GND
PWR
DC-DC Ground.
Internal ground for the DC-DC converter.
42
PD
Power Down.
A logic 1 powers off the DC-DC converter.
Connect to logic 0 for normal operation.
43
GND
A
Analog Ground.
Normally connected to system ground.
*On Ag1460 these pins are used for internal connection, and must be left unconnected.
Silver Telecom 2004
相關PDF資料 |
PDF描述 |
|---|---|
| AG1460S | QUAD 5V RINGING SLIC |
| AG2120 | FULLY FEATURED PSTN INTERFACE |
| AG2130 | LOW COST PSTN INTERFACE |
| AG2410 | HIGH PERFORMANCE QUAD TRUNK |
| AG603-89 | InGaP HBT Gain Block |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AG1460S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUAD 5V RINGING SLIC |
| AG15 | 制造商:Ferraz Shawmut 功能描述: |
| AG150 _B0 _10001 | 制造商:PanJit Touch Screens 功能描述: |
| AG15042 | 制造商:Woodhead Molex 功能描述:SENSOR CONNECTOR 制造商:Woodhead Molex 功能描述:SENSOR CONNECTOR; For Use With:Brad Nano-Change Multiport Products; Accessory Type:Closure Cap ;RoHS Compliant: Yes 制造商:Woodhead Molex 功能描述:Nano-Change Multi-Ports Closure Caps |
| AG15042B004 | 制造商:Panasonic Industrial Company 功能描述:ADAPTER |
發布緊急采購，3分鐘左右您將得到回復。