- 您現在的位置：買賣IC網 > PDF目錄379664 > AM79231JC (Electronic Theatre Controls, Inc.) Intelligent Subscriber Line Interface Circuit (ISLIC) PDF資料下載
參數資料
| 型號： | AM79231JC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Intelligent Subscriber Line Interface Circuit (ISLIC) |
| 中文描述： | 智能用戶線接口電路（ISLIC） |
| 文件頁數： | 8/28頁 |
| 文件大小： | 278K |
| 代理商： | AM79231JC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
8
Am79231 Data Sheet
PIN DESCRIPTIONS
Pin
Pin Name
I/O
Description
AD, BD
BGND
CREF
GND
HPA, HPB
A, B Line Drivers
Ground
+3.3 VDC
Ground
High-Pass Filter Ca-
pacitor
Longitudinal Current
Sense
Metallic Current Sense
O
Provide the currents to the A and B leads of the subscriber loop.
Ground return for high and low battery supplies.
VCCD reference. It is the digital high logic supply rail, used by the ISLIC to ISLAC interface.
Analog and digital ground return for VCC.
These pins connect to CHP, the external high-pass filter capacitor that separates the DC
loop-voltage from the voice transmission path.
ILG is proportional to the common-mode line current (IAD
–
IBD), except in disconnect mode,
where ILG is proportional to the current into grounded SB.
IMT is proportional to the differential line current (IAD + IBD), except in disconnect mode,
where IMT is proportional to the current into grounded SA. The Am79231 indicates thermal
overload by pulling IMT to CREF.
The LD pin controls the input latch and responds to a 3-level input. When the LD pin is a
logic 1 ( >(Vref+0.3V) ), the logic levels on P1
–
P3 latch into the Am79231 control register
bits that operate the mode-decoder. When the LD pin is a logic 0 ( <(Vref-0.3V) ), the logic
levels on P1
–
P3 latch into the Am79231 control register bits that control the relay drivers
(RD1
–
RD3). When the LD pin level is at ~VREF, the control register contents are locked.
Inputs to the latch for the operating-mode decoder and the relay-drivers.
Collector connection for ring relay driver. Emitter internally connected to BGND.
Collector connection for relay 2 driver. Emitter internally connected to RYE
Collector connection for relay 3 driver. Emitter internally connected to RYE.
The metallic current between AD and BD is equal to 500 times the current into this pin.
Networks that program receive gain and two-wire impedance connect to this node. This input
is at a virtual potential of VREF.
This is used during Legerity testing. In the application, this pin must be left floating.
Emitter connection for R2 and R3. Normally connected to relay ground.
O
ILG
O
IMT
O
LD
Register Load
I
P1
–
P3
R1
R2
R3
RSN
Control Bus
Ring Relay Driver
Relay 2 Driver
Relay 3 Driver
Receive Summing
Node
I
O
O
O
I
RSVD
RYE
Reserved
Relay 2, 3 Common
Emitter
A, B Lead Voltage
Sense
Thermal Management
O
SA, SB
I
Sense the voltages on the line side of the fuse resistors at the A and B leads. External sense
resistors, RSA and RSB, protect these pins from lightning or power-cross.
External resistors connected from TMP to TMS and TMN to VBL to offload excess power
from the Am79231.
Connection to high-battery supply used for ringing and long loops. Connects to the substrate.
When only a single battery is available, it connects to both VBH and VBL.
Connection to low-battery supply used for short loops. When only a single battery is available,
this pin can be connected to VBH.
Positive supply for low voltage analog and digital circuits in the Am79231.
Sets the DC longitudinal voltage of the Am79231. It is the reference for the longitudinal control
loop. When the VLB pin is greater than VREF, the Am79231 sets the longitudinal voltage to
a voltage approximately half-way between the positive and negative power supply battery
rails. When the VLB pin is driven to levels between 0V and VREF, the longitudinal voltage
decreases linearly with the voltage on the VLB pin.
The ISLAC chip provides this voltage which is used by the Am79231 for internal reference
purposes. All analog input and output signals interfacing to the ISLAC chip are referenced
to this pin.
Scaled-down version of the voltage between the sense points SA and SB on this pin.
The voltage between this pin and VREF is a scaled down version of the AC component of
the voltage sensed between the SA and SB pins. One end of the two-wire input impedance
programming network connects to VTX. The voltage at VTX swings positive and negative
with respect to VREF.
TMP,
TMN, TMS
VBH
Battery (Power)
VBL
Battery (Power)
VCC
VLB
+5 V Power Supply
Longitudinal Voltage
I
VREF
1.4 V Analog Refer-
ence
I
VSAB
VTX
Loop Voltage
4-Wire Transmit Signal
O
O
相關PDF資料 |
PDF描述 |
|---|---|
| AM8127LTB | AM8127 Clock Generator |
| AMZ8127 | AM8127 Clock Generator |
| AM8127XTB | AM8127 Clock Generator |
| AM8127 | AM8127 Clock Generator |
| AM8127DC | Circular Connector; MIL SPEC:MIL-DTL-38999 Series II; Body Material:Aluminum; Series:MS27508; Number of Contacts:22; Connector Shell Size:12; Connecting Termination:Crimp; Circular Shell Style:Box Mount Receptacle |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM7924JC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Interface Circuit |
| AM7924SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM7926-1VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM7926-2VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| AM7926-3VC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。