- 您現在的位置：買賣IC網 > Datasheet目錄60 > ATS617LSGTN-T (Allegro Microsystems Inc)IC HALL EFFECT GEAR SENSOR 4SIP Datasheet資料下載
參數資料
| 型號： | ATS617LSGTN-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 11/16頁 |
| 文件大小： | 489K |
| 描述： | IC HALL EFFECT GEAR SENSOR 4SIP |
| 產品培訓模塊： | Current Sensor |
| 標準包裝： | 1 |
| 傳感范圍： | 60G |
| 類型： | 專用型 |
| 電源電壓： | 4.5 V ~ 24 V |
| 電流 - 電源： | 12mA |
| 電流 - 輸出（最大）： | 55mA |
| 輸出類型： | 數字，開路集電極 |
| 特點： | 輪齒類型 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1142 (CN2011-ZH PDF) |
| 其它名稱： | 620-1326-6 |
Dynamic, Self-Calibrating, Peak-Detecting, Differential
Hall Effect Gear Tooth Sensor IC
ATS617LSG
11
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Assembly Description The ATS617 gear-tooth sensor IC is a
Hall IC/rare-earth pellet configuration that is fully optimized to
provide detection of gear tooth edges. This device is packaged in
a molded miniature plastic body that has been optimized for size,
ease of assembly, and manufacturability. High operating tem-
perature materials are used in all aspects of construction.
After proper power is applied to the component, the chip is
capable of instantly providing digital information that is repre-
sentative of the profile of a rotating gear. No additional optimi-
zation or processing circuitry is required. This ease of use should
reduce design time and incremental assembly costs for most
applications.
Hall Technology The ATS617 contains a single-chip dif-
ferential Hall effect sensor IC, a samarium cobalt pellet, and a
flat ferrous pole piece (figure 2). The Hall IC consists of 2 Hall
elements (spaced 2.2 mm apart) located so as to measure the
magnetic gradient created by the passing of a ferrous object. The
two elements measure the magnetic gradient and convert it to an
analog voltage that is then processed in order to provide a digital
output signal.
The Hall IC is self-calibrating and also possesses a tempera-
ture compensated amplifier and offset cancellation circuitry. Its
voltage regulator provides supply noise rejection throughout the
operating voltage range. Changes in temperature do not greatly
affect this device due to the stable amplifier design and the offset
rejection circuitry. The Hall transducers and signal processing
electronics are integrated on the same silicon substrate, using a
proprietary BiCMOS process.
Internal Electronics The processing circuit uses a patented
peak detection scheme to eliminate magnet and system offsets.
This technique allows dynamic coupling and filtering of offsets
without the power-up and settling time disadvantages of classical
high-pass filtering schemes. The peak signal of every tooth and
valley is detected by the filter and is used to provide an instant
reference for the operate and release point comparator. In this
manner, the thresholds are adapted and referenced to individual
signal peaks and valleys, providing immunity to zero line varia-
tion from installation inaccuracies (tilt, rotation, and off-center
placement), as well as for variations caused by target and shaft
eccentricities.
The ATS617 also includes self-calibration circuitry that is
engaged at power on. The signal amplitude is measured, and
then the device gain is normalized. In this manner switchpoint
drift versus air gap is minimized, and excellent timing accuracy
can be achieved.
The AGC (Automatic Gain Control) circuitry, in conjunction
with a unique hysteresis circuit, also eliminates the effect of gear
edge overshoot as well as increases the immunity to false switch-
ing caused by gear tooth anomalies at close air gaps. The AGC
circuit sets the gain of the device after power-on.
Functional Description
Target (Gear)
Back-Biasing
Rare-Earth Pellet
South Pole
North Pole
Case
(Pin 1 Side)
(Pin n >1 Side)
Hall IC
Pole Piece
Element Pitch
(Concentrator)
Dual-Element
Hall Effect Device
Hall Element 1
Hall Element 2
Figure 2. Relative motion of the target is detected by the dual Hall ele-
ments mounted on the Hall IC.
Figure 3. The peaks in the resulting differential signal are used to set the
operate, B
OP
, and release, B
RP
, switchpoints.
Device Output
V
OUT
B
RP
Differential
Input Signal
V
PROC
V+
V
0
V
CC
V
OUT(sat)
B
OP
B
RP
B
OP
相關PDF資料 |
PDF描述 |
|---|---|
| ATS625LSGTN-T | IC SENSOR GEAR TOOTH 4-SIP |
| ATS627LSGTN-T | IC HALL EFFECT GEAR SENSOR 4-SIP |
| ATS635LSETN-T | IC SENSOR GEAR TOOTH 4-SIP |
| ATS643LSHTN-I2-T | IC SENSOR GEAR TOOTH 4-SIP |
| ATS645LSHTN-I1 | IC SENSOR GEAR TOOTH 4-SIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS622LSB | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:TRUE ZERO-SPEED HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS625LSG | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor |
| ATS625LSGTN | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS625LSGTN-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。