- 您現在的位置：買賣IC網 > PDF目錄370018 > PROGRAMMING Programming the M16C/62 Flash in Asynchronous Serial ModeApplication Note 214K/JUL.07.03 PDF資料下載
參數資料
| 型號： | PROGRAMMING |
| 英文描述： | Programming the M16C/62 Flash in Asynchronous Serial ModeApplication Note 214K/JUL.07.03 |
| 中文描述： | 異步串行編程ModeApplication注意214K/JUL.07.03的雙隨機PWM閃光 |
| 文件頁數： | 1/7頁 |
| 文件大小： | 214K |
| 代理商： | PROGRAMMING |
APPLICATION NOTE
M16C/62
Programming the M16C/62 Flash in Asynchronous Serial Mode
1.0 Abstract
The following article describes using an asynchronous serial port and the FlashStart application to program the
user flash memory of the M16C/62 series of microcontrollers. This is referred to in the M16C/62 data sheets as
the “Standard Serial I/O Mode 2” method of flash programming.
2.0 Introduction
The Renesas M16C/62 series of microcontrollers is a 16-bit family of MCUs, based on Renesas’ popular M16C
CPU core. These parts provide high memory efficiency, power-saving ability, low noise emission, and improved
noise immunity. The flash versions of the device contain flash memory that can be rewritten with a single voltage.
The M16C/62 flash can be programmed using one of three methods: Parallel I/O Mode, Standard Serial I/O
Mode, and CPU Rewrite Mode. Standard Serial I/O Mode can be further divided into a synchronous mode
(Standard Serial I/O Mode 1) and an asynchronous mode (Standard Serial I/O Mode 2). The flash memory is
divided into two major blocks, a user program area and a boot ROM area. The user program area is for the
normal application program and data. Any program in the boot ROM area is accessed only when a special
hardware reset sequence is initiated. This boot ROM area has a control program stored in it when shipped from
the factory. The program allows asynchronous or synchronous serial programming of the user area of the flash.
Changes to the boot area of the flash can only be made using Parallel I/O Mode.
Renesas provides a Windows
based program, FlashStart, to serially download code (in S-record format) to
M16C/62 MCUs. The website for downloading the program is listed in section 5
.0 Reference
3.0 Hardware Requirements for Asynchronous Serial Programming
The CNVSS pin on the microcontroller is the primary control line that determines whether the user area of the
flash or the boot area is accessed after the release of a reset. If the CNVSS pin is low the device will always
access the user flash area and will start in single chip mode. To execute the asynchronous serial rewrite program
in the boot area of the flash, the pins listed below must be connected as shown when a reset is performed (either
during power-up of the microcontroller or by forcing the Reset line low and then setting it high). Figure 1 shows a
typical connection.
REU05B0013-0100Z
June 2003
Page 1 of 6
相關PDF資料 |
PDF描述 |
|---|---|
| PRS07 | Fast soft-recovery rectifiers |
| PRS07D | Fast soft-recovery rectifiers |
| PRS07G | Fast soft-recovery rectifiers |
| PRS07J | Fast soft-recovery rectifiers |
| PRS28G | Packet Routing Switch For Multigigabit-Per-Port Switch Solution(網絡通信用信息包通路轉換開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PROGSHIELD | 功能描述:PROGRAMMER SHIELD 制造商:particle industries, inc. 系列:- 零件狀態:在售 類型:編程器 配套使用產品/相關產品:Photon 內容:板 標準包裝:1 |
| PROG-WIN2 | 功能描述:LABEL SOFTWARE WINDOWS ADV 3.5" RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| PROGWIN2CD | 制造商:Panduit Corp 功能描述:Unspecified Tools & Accessories SOFTWARE |
| PROG-WIN2CD | 功能描述:CD ROM WINDOWS PAN-MARK LABELING RoHS:否 類別:編程器，開發系統 >> 軟件 系列:- 標準包裝:1 系列:ISE® 設計套件 類型:訂閱 適用于相關產品:Xilinx FPGAs 其它名稱:Q4986209T1081384 |
| PROHDCART | 制造商:OMNIMOUNT 功能描述:FLAT PANEL MOBILE CART FITS 37 IN - 55 IN FLAT PANELS |
發布緊急采購，3分鐘左右您將得到回復。