欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: C062G102B2CK5CM
廠商: KEMET Corporation
英文描述: CONNECTOR ACCESSORY
中文描述: 連接器附件
文件頁數: 4/40頁
文件大小: 580K
代理商: C062G102B2CK5CM
MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
4
KEMET
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure.
The entire structure is
fired at high temperature to produce a monolithic
block
which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
a wide range of characteristics. The EIA standard for
ceramic dielectric capacitors (RS-198) divides ceramic
dielectrics into the following classes:
Class I:
Temperature compensating capacitors,
suitable for resonant circuit application or other appli-
cations where high Q and stability of capacitance char-
acteristics are required. Class I capacitors have
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
from materials which are not ferro-electric, yielding
superior stability but low volumetric efficiency. Class I
capacitors are the most stable type available, but have
the lowest volumetric efficiency.
Class II:
Stable capacitors, suitable for bypass
or coupling applications or frequency discriminating
circuits where Q and stability of capacitance char-
acteristics are not of a major importance. Class II
capacitors have temperature characteristics of ± 15%
or less. They are made from materials which are
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
temperature, voltage, frequency and time.
Class III:
General purpose capacitors, suitable
for by-pass coupling or other applications in which
dielectric losses, high insulation resistance and
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
II capacitors except for temperature characteristics,
which are greater than ± 15%. Class III capacitors
have the highest vol
umetric efficiency and poorest
stability of any type.
KEMET leaded ceramic capacitors are offered in
the three most popular temperature characteristics:
C0G:
Class I, with a temperature coefficient of 0 ±
30 ppm per degree C over an operating
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
X7R:
Class II, with a maximum capacitance
change of ± 15% over an operating temperature
range of - 55°C to + 125°C.
Z5U:
Class III, with a maximum capacitance
change of + 22% - 56% over an operating tem-
perature range of + 10°C to + 85°C.
Specified electrical limits for these three temperature
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
TEMPERATURE CHARACTERISTICS
C0G
X7R
PARAMETER
Z5U
Dissipation Factor: Measured at following conditions:
C0G — 1 kHz and 1 vrms if capacitance > 1000 pF
1 MHz and 1 vrms if capacitance
1000 pF
X7R — 1 kHz and 1 vrms*
Z5U — 1 kHz and 0.5 vrms
0.15%
2.5%
4.0%
Dielectric Strength: 2.5 times rated DC voltage.
Pass Subsequent IR Test
Insulation Resistance (IR): At rated DC voltage,
1,000 M
-μF
or 100 G
1,000 M
-μF
or 100 G
1,000 M
-μF
or 10 G
whichever of the two is smaller
Temperature Characteristics: Range, °C
-55 to 125
0 ± 30 ppm/°C
-55 to 125
±15%
+10 to 85
+22%, -56%
Capacitance Change without
DC voltage
* 1 MHz and 1 vrms if capacitance
100 pF on military product.
Table I
相關PDF資料
PDF描述
C062G102B2CK5CP CONNECTOR ACCESSORY
C062G102B2CX5CA CONNECTOR ACCESSORY
C066K102K2X5CR MILITARY SPECIFCATIONS ON BACK
C066K102K2X5CS MILITARY SPECIFCATIONS ON BACK
C066K102K5BX5CA MILITARY SPECIFCATIONS ON BACK
相關代理商/技術參數
參數描述
C062G102B2CK5CP 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK
C062G102B2CX5CA 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK
C062G102B2CX5CM 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK
C062G102B2CX5CP 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK
C062G102B2G5CA 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK
主站蜘蛛池模板: 察隅县| 成安县| 府谷县| 平乡县| 缙云县| 云浮市| 金溪县| 兴安县| 上高县| 西畴县| 澜沧| 贞丰县| 神农架林区| 临江市| 苏尼特右旗| 疏勒县| 吉首市| 股票| 隆回县| 永年县| 平山县| 茌平县| 广南县| 且末县| 昆山市| 广水市| 阆中市| 太仆寺旗| 台南县| 佳木斯市| 天台县| 常熟市| 磴口县| 米易县| 慈利县| 崇明县| 花莲县| 象州县| 盐山县| 康乐县| 资溪县|