- 您現在的位置：買賣IC網 > PDF目錄374059 > C062G102J5G5CA (KEMET Corporation) T-PNP-DIFFERENTIAL AMP PDF資料下載
參數資料
| 型號： | C062G102J5G5CA |
| 廠商： | KEMET Corporation |
| 元件分類： | 運動控制電子 |
| 英文描述： | T-PNP-DIFFERENTIAL AMP |
| 中文描述： | 背面軍事SPECIFCATIONS |
| 文件頁數： | 4/40頁 |
| 文件大小： | 580K |
| 代理商： | C062G102J5G5CA |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
4
KEMET
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure.
The entire structure is
fired at high temperature to produce a monolithic
block
which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
a wide range of characteristics. The EIA standard for
ceramic dielectric capacitors (RS-198) divides ceramic
dielectrics into the following classes:
Class I:
Temperature compensating capacitors,
suitable for resonant circuit application or other appli-
cations where high Q and stability of capacitance char-
acteristics are required. Class I capacitors have
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
from materials which are not ferro-electric, yielding
superior stability but low volumetric efficiency. Class I
capacitors are the most stable type available, but have
the lowest volumetric efficiency.
Class II:
Stable capacitors, suitable for bypass
or coupling applications or frequency discriminating
circuits where Q and stability of capacitance char-
acteristics are not of a major importance. Class II
capacitors have temperature characteristics of ± 15%
or less. They are made from materials which are
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
temperature, voltage, frequency and time.
Class III:
General purpose capacitors, suitable
for by-pass coupling or other applications in which
dielectric losses, high insulation resistance and
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
II capacitors except for temperature characteristics,
which are greater than ± 15%. Class III capacitors
have the highest vol
umetric efficiency and poorest
stability of any type.
KEMET leaded ceramic capacitors are offered in
the three most popular temperature characteristics:
C0G:
Class I, with a temperature coefficient of 0 ±
30 ppm per degree C over an operating
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
X7R:
Class II, with a maximum capacitance
change of ± 15% over an operating temperature
range of - 55°C to + 125°C.
Z5U:
Class III, with a maximum capacitance
change of + 22% - 56% over an operating tem-
perature range of + 10°C to + 85°C.
Specified electrical limits for these three temperature
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
TEMPERATURE CHARACTERISTICS
C0G
X7R
PARAMETER
Z5U
Dissipation Factor: Measured at following conditions:
C0G — 1 kHz and 1 vrms if capacitance > 1000 pF
1 MHz and 1 vrms if capacitance
≤
1000 pF
X7R — 1 kHz and 1 vrms*
Z5U — 1 kHz and 0.5 vrms
0.15%
2.5%
4.0%
Dielectric Strength: 2.5 times rated DC voltage.
Pass Subsequent IR Test
Insulation Resistance (IR): At rated DC voltage,
1,000 M
-μF
or 100 G
1,000 M
-μF
or 100 G
1,000 M
-μF
or 10 G
whichever of the two is smaller
Temperature Characteristics: Range, °C
-55 to 125
0 ± 30 ppm/°C
-55 to 125
±15%
+10 to 85
+22%, -56%
Capacitance Change without
DC voltage
* 1 MHz and 1 vrms if capacitance
≤
100 pF on military product.
Table I
相關PDF資料 |
PDF描述 |
|---|---|
| C052G102J1CH5CP | MILITARY SPECIFCATIONS ON BACK |
| C052G102J2G5CA | MILITARY SPECIFCATIONS ON BACK |
| C062G102J2G5CA | MILITARY SPECIFCATIONS ON BACK |
| C052G102J2G5CM | MILITARY SPECIFCATIONS ON BACK |
| C062G102J2G5CM | MILITARY SPECIFCATIONS ON BACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C062G102J5G5CM | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20 |
| C062G102J5G5CP | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20 |
| C062G102J5G5CR | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20 |
| C062G102J5G5CS | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20 |
| C062G102K1C0G5CA | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:CERAMIC MOLDED/AXIAL & RADIAL - MIL-PRF-20 |
發布緊急采購，3分鐘左右您將得到回復。