- 您現在的位置：買賣IC網 > PDF目錄374055 > C066T102M5BX5CP (KEMET Corporation) 18-Bit Universal Bus Transceivers with 3-State Outputs 56-SSOP -40 to 85 PDF資料下載
參數資料
| 型號： | C066T102M5BX5CP |
| 廠商： | KEMET Corporation |
| 英文描述： | 18-Bit Universal Bus Transceivers with 3-State Outputs 56-SSOP -40 to 85 |
| 中文描述： | 背面軍事SPECIFCATIONS |
| 文件頁數： | 33/40頁 |
| 文件大?。?/td> | 580K |
| 代理商： | C066T102M5BX5CP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
33
KEMET
CERAMIC LEADED
PACKAGING INFORMATION
T
Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)
Figure 3: Standard Reel
Figure 1
3
1
/
"
(82.6)
.655"
±
0.010"
(16.6
±
0.25)
12"
(30.48 cm)
.059" to .315"
Greater Than
Over All
Height
of Taped
Components
*
Hub
1/8"
(3.18)
Ceramic Radial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Ceramic Capacitors for automatic
insertion per EIA specification RS-468. Parts are taped to a
tagboard carrier strip, and wound on a reel as shown in
Figure 1. Kraft paper interleaving is inserted between the
layers of capacitors on the reel. Ammopack is also available,
with the same lead tape configuration and package quantities.
KEMET
KEMET
Kraft Paper
Interleaving
Carrier Tape
Carrier Strip
Adhesive Tape
* Lead spacings are 2.54mm
(.10") center-to-center.
** Lead spacings are 5.08mm
(.20") center-to-center.
C317**
C322**
C323**
P
2
C333**
H
W
0
W
2
W
2
P
0
T
H
1
L
1
D
0
C315*
C320*
CK05**
CKR05**
C052**
C056**
C066**
CK06**
CKR06**
C062**
C330**
C340**
P
1MM Max.
(.039")
Tape
Carrier
H
P1
F
Figure 2: Lead Tape Configuration (See Table Below)
W
H
0
Sprocket Hole Diameter
Sprocket Hole Pitch
Component Pitch
Lead Spacing (1)
Sprocket Hole Center
to Lead Center (1)
Sprocket Hole Center
to Component Center
Height to Seating Plane
(straight leads) (2)
Component Height
Above Tape Center
(1) Measured at the egress from the carrier tape, on the component side.
(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:
7301 =
7303 =
Recommended for parts with straight leads.
Dimension
Symbol
Do
Nominal
mm (inch)
4.0 (.157)
Tolerance
mm (inch)
±
0.2 (.008)
Dimension
Height to Seating
Plane (formed leads) (2)
Component Alignment
Symbol
H
0
Nominal
mm (inch)
C7301 C7303
16.0 (.630) 18.0 (.709)
4.0 (.157)
Tolerance
mm (inch)
C7301 C7303
±
0.5 (.020) Minimum
±
0.2 (.008)
Lead Protrusion
Composite Tape
Thickness
Overall Tape and
Lead Thickness
Carrier Tape Width
Hold-Down Tape
Width
Hold-Down Tape
Location
P0
P
F
P1
P2
H
H1
±
0.3 (.012)
±
0.3 (.012)
+0.6 -0.2
(+.024 -.008)
±
0.7 (.028)
±
1.3 (.051)
C7301 C7303
±
0.5 (.020) Minimum
Maximum
1.0 (.039)
0.7 (.051)
1.5 (.059)
18.0 (.709)
5.0 (.197)
3.0 (.118)
h
L1
t
T
W
W0
W2
Maximum
±
0.2 (.008)
Maximum
+1.0 - 0.5
(+.039 -.020)
Minimum
Maximum
12.7 (.500)
12.7 (.500)
5.08 2.54
(.20) (.10)
3.81 5.08
(.150) (.200)
6.35 (.250)
C7301 C7303
16.0 (.630) 18.0 (.709)
32.2 (1.27)
Recommended for parts with formed leads.
Example: C322C104K5R5CA7301
Example: C320C104K5R5CA7303
相關PDF資料 |
PDF描述 |
|---|---|
| C066T102M5BX5CR | MILITARY SPECIFCATIONS ON BACK |
| C066T102M5BX5CS | MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CA | MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CM | MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CP | MILITARY SPECIFCATIONS ON BACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C066T102M5BX5CR | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK |
| C066T102M5BX5CS | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CA | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CM | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK |
| C066T102M5X5CP | 制造商:KEMET 制造商全稱:Kemet Corporation 功能描述:MILITARY SPECIFCATIONS ON BACK |
發布緊急采購，3分鐘左右您將得到回復。