- 您現在的位置：買賣IC網 > PDF目錄257681 > CAT1026SI-25 (ON SEMICONDUCTOR) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | CAT1026SI-25 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 5/17頁 |
| 文件大小： | 103K |
| 代理商： | CAT1026SI-25 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
13
CAT1026, CAT1027
Doc No. 3010, Rev. H
Immediate/Current Address Read
The CAT1026 and CAT1027 address counter contains
the address of the last byte accessed, incremented by
one. In other words, if the last READ or WRITE access
was to address N, the READ immediately following
would access data from address N + 1. For N = E = 255,
the counter will wrap around to zero and continue to
clock out valid data. After the CAT1026 and CAT1027
receive a slave address (with the R/
W bit set t o one), an
acknowledge is issued, and the requested 8-bit byte is
transmitted. The master device does not send an
acknowledge, but will generate a STOP condition.
Selective/Random Read
Selective/Random READ operations allow the Master
device to select at random any memory location for a
READ operation. The Master device first performs a
‘dummy’ write operation by sending the START condition,
slave address and byte addresses of the location it
wishes to read. After the CAT1026 and CAT1027
acknowledge, the Master device sends the START
condition and the slave address again, this time with the
R/
W bit set to one. The CAT1026 and CAT1027 then
respond with an acknowledge and sends the 8-bit byte
requested. The master device does not send an
acknowledge but will generate a STOP condition.
Sequential Read
The Sequential READ operation can be initiated by
either the Immediate Address READ or Selective READ
operations. After the CAT1026 and CAT1027 send the
inital 8-bit byte requested, the Master responds with an
acknowledge which tells the device it requires more
data. The CAT1026 and CAT1027 will continue to output
an 8-bit byte for each acknowledge, thus sending the
STOP condition.
The data being transmitted from the CAT1026 and
CAT1027 is sent sequentially with the data from address
N followed by data from address N+1. The READ
operation address counter increments all of the CAT1026
and CAT1027 address bits so that the entire memory
array can be read during one operation.
SLAVE
ADDRESS
S
A
C
K
N
O
A
C
K
S
T
O
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
BYTE
ADDRESS (n)
S
A
C
K
DATA n
SLAVE
ADDRESS
A
C
K
S
T
A
R
T
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+x
DATA n
A
C
K
A
C
K
DATA n+1
A
C
K
S
T
O
P
N
O
A
C
K
DATA n+2
A
C
K
P
SLAVE
ADDRESS
Figure 12. Selective Read Timing
Figure 13. Sequential Read Timing
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1026VI-28TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| CAT1026VI-30TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| CAT1027YI-30TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CQ1001-7R | 1-OUTPUT 82 W DC-DC REG PWR SUPPLY MODULE |
| CAT1026SE-45TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1026SI-25-TE13 | 功能描述:監控電路 2K bit 2.5V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026SI-28 | 功能描述:監控電路 2K bit 2.8V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026SI-28-TE13 | 功能描述:監控電路 2K bit 2.8V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026SI-30 | 功能描述:監控電路 2K bit 3V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1026SI-30-TE13 | 功能描述:監控電路 2K bit 3V Ind Temp RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。