- 您現在的位置：買賣IC網 > PDF目錄257682 > CAT1027YI-30TE13 (ON SEMICONDUCTOR) 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | CAT1027YI-30TE13 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | LEAD AND HALOGEN FREE, TSSOP-8 |
| 文件頁數： | 2/20頁 |
| 文件大小： | 153K |
| 代理商： | CAT1027YI-30TE13 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
10
CAT1026, CAT1027
Doc. No. 3010, Rev. K
ACKNOWLEDGE
After a successful data transfer, each receiving device
is required to generate an acknowledge. The
acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8 bits
of data.
The CAT1026 and CAT1027 respond with an
acknowledge after receiving a START condition and its
slave address. If the device has been selected along
with a write operation, it responds with an acknowledge
after receiving each 8-bit byte.
When the CAT1026 and CAT1027 begin a READ mode
it transmits 8 bits of data, releases the SDA line and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT1026 and CAT1027 will
continue to transmit data. If no acknowledge is sent by
the Master, the device terminates data transmission and
waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information (with
the R/
W bit set to zero) to the Slave device. After the Slave
generates an acknowledge, the Master sends a 8-bit
address that is to be written into the address pointers of
the device. After receiving another acknowledge from the
Slave, the Master device transmits the data to be written
into the addressed memory location. The CAT1026 and
CAT1027 acknowledge once more and the Master
generates the STOP condition. At this time, the device
begins an internal programming cycle to non-volatile
memory. While the cycle is in progress, the device will not
respond to any request from the Master device.
Figure 8. Slave Address Bits
CAT
Default Configuration
1
010
0
R/W
START BIT
SDA
STOP BIT
SCL
Figure 6. Start/Stop Timing
ACKNOWLEDGE
1
START
SCL FROM
MASTER
89
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 7. Acknowledge Timing
相關PDF資料 |
PDF描述 |
|---|---|
| CQ1001-7R | 1-OUTPUT 82 W DC-DC REG PWR SUPPLY MODULE |
| CAT1026SE-45TE13 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| CAT1026RD2I-45 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO8 |
| CAT1027PE-25 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT1027UI-30 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1027YI42 | 制造商:ON Semiconductor 功能描述:CPU SUPERVISOR WITH 2K EEPROM - Rail/Tube |
| CAT1027YI-42-GT3 | 功能描述:監控電路 CPU SUP W/2K EEPROM RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1027YI-42-T3 | 制造商:ON Semiconductor 功能描述:CPU SUPERVISOR WITH 2K EEPROM - Tape and Reel |
| CAT1027YI45 | 制造商:ON Semiconductor 功能描述:CPU SUPERVISOR WITH 2K EEPROM - Rail/Tube |
| CAT1027YI-45-GT3 | 功能描述:監控電路 CPU SUP W/2K EEPROM RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。