欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CCW128-0629-12CB95
元件分類: 插座
英文描述: BGA128, IC SOCKET
封裝: ROHS COMPLIANT
文件頁數: 3/8頁
文件大小: 1168K
代理商: CCW128-0629-12CB95
Socket Mounting Recommendations and Reflow Profile
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland
Phone +41-21-781 08 10 www.e-tec.com info@e-tec.com
E-tec Socket Mounting Recommendations
PRELIMINARY
1
Purpose
This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)
sockets to the printed circuit board (PCB). The recommendations described here are guidelines
only, and modifications may be needed for your particular socket, PCB, and process.
Application
The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist
Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-
pin technology. This technology allows the pins to be soldered to the PCB while still providing
compliance to the device under test (DUT) via springs located at the other end of the pin. The
pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the
sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or
any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating
Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder
paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil
is required. Once the paste has been applied, a standard reflow process is then used to solder the
socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,
the system is then ready to be used.
Locating Pegs
Although designed to mount to the same footprint as the IC, with just a small amount of
additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are
typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.
These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s
pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs
to be soldered to the PCB for better mechanical stability during everyday use and handling of the
socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-
pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints
may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M
Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is
required to ensure mechanical and electrical integrity. Recommended stencil dimensions are
given in the next section of this document.
相關PDF資料
PDF描述
CCW484-1270-26AB95 BGA484, IC SOCKET
CUW049-1028-07CB95 BGA49, IC SOCKET
CUW049-1228-07CB95L BGA49, IC SOCKET
CCW484-0728-26AB95L BGA484, IC SOCKET
CUW484-1270-22AB95L BGA484, IC SOCKET
相關代理商/技術參數
參數描述
CCW128R20JLFTR 制造商:IRC 功能描述:8.2 OHM 1/2W 5% WW
CCW129R10JLFTR 制造商:IRC 功能描述:9.1 OHM 1/2W 5% WW
CCW12R00JLFTR 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 2 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW12R100JLFTR 制造商:IRC 功能描述:.1 OHM 1/2W 5% WW
CCW12R110JLFTR 制造商:IRC 功能描述:.11 OHM 1/2W 5% WW
主站蜘蛛池模板: 林甸县| 金阳县| 宁远县| 会宁县| 天全县| 孝义市| 崇明县| 聂拉木县| 泾源县| 措美县| 黄龙县| 卢氏县| 分宜县| 乌兰浩特市| 尖扎县| 蓬溪县| 米林县| 五莲县| 花莲市| 道孚县| 建湖县| 东乡族自治县| 南安市| 南木林县| 乌拉特后旗| 陆良县| 同江市| 长兴县| 中牟县| 龙陵县| 永登县| 梓潼县| 加查县| 鹤峰县| 犍为县| 乾安县| 阿拉善左旗| 同德县| 弥渡县| 苏尼特右旗| 汾阳市|