欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CK1301-7ERDDB1
元件分類: 電源模塊
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝: METAL, CASE K02, MODULE
文件頁數: 6/27頁
文件大小: 640K
代理商: CK1301-7ERDDB1
Rugged Environment
DC-DC Converters >100 W
K-Family
Edition 2/96 - Melcher AG
8 - 15
MELCHER
The Power Partners.
8.1
Test Sockets (Main output only 1)
Test sockets for measuring the output voltage
Uo1 are lo-
cated at the front of the module. The positive test socket is
protected by a series resistor (see Functional Description,
block diagrams). The voltage measured at the test sockets
is approximately 30 mV lower than the value measured at
the output terminals.
1 In case of double output units externally connected in series for
Uo = 24 V, 30 V or 48 V the monitored output voltage is 12 V,
15 V or 24 V respectively.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diode
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Inhibit Function
The outputs of a module may be enabled or disabled by
means of a logic signal (TTL, CMOS etc.) applied to the in-
hibit input. If the inhibit function is not required, connect the
inhibit pin 18 to pin 14 to enable the outputs (active low
logic, fail safe).
Fig. 10
Typical output response as a function of inhibit control
Table 9: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Uinh Inhibit
Uo = on Ui min…Ui max
–50
0.8
V
voltage
Uo = off
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
Uo nom
Output
tr
tf
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
– Not more than 5 units should be connected in parallel.
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables compensation for voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that
Uo max (between Vo1+ and Vo1–) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to "Application Notes ".
To ensure correct operation, both sense lines should be
connected to their respective power outputs and the volt-
age difference between any sense line and its respective
power output pin (as measured on the connector) should
not exceed the following values:
Table 10: Voltage compensation allowed using sense
lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12 V, 15 V
< 1.0 V
< 0.25 V
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
相關PDF資料
PDF描述
CK1501-7PDD 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
CK1601-7ERDDT 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
CK2540-9RDDB1 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CAT812JTBI-GT3 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4
CAT1023JE-25TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
相關代理商/技術參數
參數描述
CK1301-7R 功能描述:DC/DC PS 1-OUT 12V 12A 150W RoHS:是 類別:電源 - 外部/內部(非板載) >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流(最大):24 VDC @ 50A 輸出 - 2 @ 電流(最大):- 輸出 - 3 @ 電流(最大):- 輸出 - 4 @ 電流(最大):- 功率(瓦特):1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H(110mm x 231mm x 156mm) 包裝:散裝 電源(瓦特)- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH
CK1301-9ER 制造商:Power-One 功能描述:DCDC - Bulk
CK1301-9ERB1 功能描述:DC/DC CONVERTER 12V 12A 制造商:bel power solutions 系列:Melcher K 包裝:散裝 零件狀態:有效 類型:隔離 電壓 - 輸入:28 ~ 140 V 輸出:12V 輸出數:1 不同電流時的輸出(最大值) - 1:12 VDC @ 12A 不同電流時的輸出(最大值) - 2:- 不同電流時的輸出(最大值) - 3:- 不同電流時的輸出(最大值) - 4:- 功率(W):144W 應用:ITE(商業),鐵路 安裝類型:底座安裝 工作溫度:-40°C ~ 71°C 效率:82% 封裝/外殼:- 大小/尺寸:6.61" 長 x 5.51" 寬 x 1.86" 高(168.0mm x 140.0mm x 47.2mm) 功率(W) - 最大值:144W 認可:cCSAus,CE,TUV 標準包裝:1
CK1301-9ERG 功能描述:DC/DC CONVERTER 制造商:bel power solutions 系列:* 零件狀態:有效 標準包裝:5
CK1381P26A 制造商:RAYMA 功能描述:
主站蜘蛛池模板: 宁晋县| 五原县| 三穗县| 大洼县| 万年县| 枣庄市| 金阳县| 新龙县| 盈江县| 广平县| 双流县| 陇西县| 商河县| 清涧县| 松原市| 阿城市| 黄浦区| 三门峡市| 隆尧县| 康马县| 深水埗区| 镇安县| 神农架林区| 玉龙| 蛟河市| 新野县| 陇南市| 康平县| 宜黄县| 安新县| 新竹县| 陆丰市| 房产| 涪陵区| 靖宇县| 邛崃市| 九寨沟县| 东辽县| 甘肃省| 五家渠市| 太仆寺旗|