- 您現在的位置：買賣IC網 > PDF目錄257694 > CK1301-9PTB2 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CK1301-9PTB2 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE K02, MODULE |
| 文件頁數： | 16/31頁 |
| 文件大小： | 637K |
| 代理商： | CK1301-9PTB2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
23/31
Due to high current values, all AK...FK units provide two in-
ternally parallel connected contacts for certain paths (pins
4/6, 8/10, 26/28 and 30/32 respectively). It is recommended
to connect load and supply to both female connector pins of
each path in order to keep the voltage drop across the con-
nector pins to an absolute minimum and to not overstress
the connector contacts if currents are higher than approx. 8
A. The connector contacts are rated 8 A over the whole
temperature range.
Make sure that there is sufficient air flow possible for con-
vection cooling. This should be verified by measuring the
case temperature when the unit is installed and operated in
the end-use application. The maximum specified case tem-
perature
TC max shall not be exceeded. See also Thermal
Considerations.
If the end-product is to be UL certified, the temperature of
the main isolation transformer should be evaluated as part
of the end-product investigation.
Check for hazardous voltages before altering any connec-
tions.
Ensure that a unit failure (e.g. by an internal short-circuit)
does not result in a hazardous condition. See also:
Safety
of operator accessible output circuit.
Cleaning Agents
In order to avoid possible damage, any penetration of
cleaning fluids is to be prevented, since the power supplies
are not hermetically sealed.
Isolation
The electric strength test is performed as factory test in ac-
cordance with IEC/EN 60950 and UL 1950 and should not
be repeated in the field. Power-One will not honour any
guarantee claims resulting from electric strength field tests.
Table 13: Isolation
Characteristic
Input to
Output to
Unit
case
output
case
output
Electric
Required according to
AK, BK
1.0
2.0 1
0.5
-
kVrms
strength
IEC/EN 60950
1.4
2.8 1
0.7
-
kV DC
test voltage
CK, DK
1.5
3.0 1
0.5
-
kVrms
EK, FK
2.1
4.2 1
0.7
-
kV DC
Actual factory test 1 s
AK, BK
2.8
5.6 1
1.4
0.14
AC test voltage equivalent
CK, DK
2.0
4.0 1
1.0
0.1
kVrms
to actual factory test
EK, FK
Insulation resistance at 500 V DC
>300
>100 2
M
1 In accordance with IEC/EN 60950 only subassemblies are tested in factory with this voltage.
2 Tested at 150 V DC.
For creepage distances and clearances refer to:
Technical
Information: Safety.
Standards and approvals
All DC-DC converters correspond to class I equipment.
They are UL recognized according to UL 1950, UL recog-
nized for Canada to CAN/CSA C22.2 No. 950-95 and LGA
approved to IEC/EN 60950 standards.
The units have been evaluated for:
Building in,
Basic insulation between input and case and double or
reinforced insulation between input and output, based
on 150 V AC/DC (AK and BK) or 250 V AC and 400 V DC
(CK, DK, EK, FK),
The use in a pollution degree 2 environment,
Connecting the input to a primary or secondary circuit
which is subject to a maximum transient rating of
2500 V.
The DC-DC converters are subject to manufacturing sur-
veillance in accordance with the above mentioned UL,
CSA, EN and with ISO 9001 standards.Cleaning Agents
In order to avoid possible damage, any penetration of
cleaning fluids is to be prevented, since the power supplies
are not hermetically sealed.
Protection Degree
Condition: Female connector fitted to the unit.
IP 30: All units except those with option P, and except
those with option D or V with potentiometer.
IP 20: All units fitted with option P, or with option D or V with
potentiometer.
相關PDF資料 |
PDF描述 |
|---|---|
| CK1301-9RD9T | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CK1301-9RDDB2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CK1501-7ERD3TB1 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CK1501-7PD4 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| CK1501-7PD8B2 | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CK1381P26A | 制造商:RAYMA 功能描述: |
| CK13BR273K | 功能描述:多層陶瓷電容器MLCC - 含引線 MOLDED AXIAL RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| CK13BR333K | 功能描述:多層陶瓷電容器MLCC - 含引線 .033UF 50V 10% RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| CK13BR333M | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Multilayer Ceramic Capacitors |
| CK13BR393K | 功能描述:多層陶瓷電容器MLCC - 含引線 MOLDED AXIAL RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
發布緊急采購，3分鐘左右您將得到回復。