欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CK1301-9RD8B1
元件分類: 電源模塊
英文描述: 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
封裝: METAL, CASE K02, MODULE
文件頁數: 6/31頁
文件大?。?/td> 637K
代理商: CK1301-9RD8B1
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
14/31
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Uinh Inhibit
Uo = on
Ui min…Ui max
–50
0.8
V
voltage
Uo = off
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Uo/Uo nom
tr
tf
06001
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that
Uo max (between Vo1+ and Vo1–) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to:
Application Notes.
To ensure correct operation, both sense lines (S+ and S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–) and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12 V, 15 V
< 1.0 V
< 0.25 V
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
Note: The output terminals Vo1+ and Vo1– must always be
connected to the load before connecting the sense lines S+
and S–, otherwise the unit will be damaged.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input: Output is disabled (
Uo = off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1–). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail
safe). For output response refer to:
Hold-up Time and Out-
put Response.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Uinh
06031
1.6
0.8
0
–0.8
–50
Uinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Uinh = 0.8 V
Uo = on
Uo = off
Uinh = 2.4 V
06032
Fig. 13
Definition of Uinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Uinh
相關PDF資料
PDF描述
CK1501-7EPD7T 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-7EPD9TB2 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-7ERD2B1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-7ERD7TB1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-7PD2T 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
CK1381P26A 制造商:RAYMA 功能描述:
CK13BR273K 功能描述:多層陶瓷電容器MLCC - 含引線 MOLDED AXIAL RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型:
CK13BR333K 功能描述:多層陶瓷電容器MLCC - 含引線 .033UF 50V 10% RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型:
CK13BR333M 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Multilayer Ceramic Capacitors
CK13BR393K 功能描述:多層陶瓷電容器MLCC - 含引線 MOLDED AXIAL RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型:
主站蜘蛛池模板: 商河县| 图们市| 肇州县| 历史| 淮北市| 高安市| 蓝田县| 衡阳县| 文安县| 朝阳市| 土默特左旗| 石楼县| 宁都县| 乌拉特中旗| 哈巴河县| 桂东县| 苗栗县| 南乐县| 洛浦县| 胶州市| 凤翔县| 阳朔县| 明水县| 新郑市| 财经| 武清区| 高淳县| 新竹市| 连平县| 定州市| 太湖县| 乌拉特中旗| 家居| 明溪县| 社旗县| 永丰县| 乌什县| 临江市| 青神县| 湖州市| 正蓝旗|