欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CK1501-7PD2T
元件分類: 電源模塊
英文描述: 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
封裝: HEAT SINK, METAL, CASE K02, MODULE
文件頁數: 6/31頁
文件大小: 637K
代理商: CK1501-7PD2T
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
14/31
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Uinh Inhibit
Uo = on
Ui min…Ui max
–50
0.8
V
voltage
Uo = off
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Uo/Uo nom
tr
tf
06001
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that
Uo max (between Vo1+ and Vo1–) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to:
Application Notes.
To ensure correct operation, both sense lines (S+ and S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–) and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12 V, 15 V
< 1.0 V
< 0.25 V
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
Note: The output terminals Vo1+ and Vo1– must always be
connected to the load before connecting the sense lines S+
and S–, otherwise the unit will be damaged.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input: Output is disabled (
Uo = off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1–). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail
safe). For output response refer to:
Hold-up Time and Out-
put Response.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Uinh
06031
1.6
0.8
0
–0.8
–50
Uinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Uinh = 0.8 V
Uo = on
Uo = off
Uinh = 2.4 V
06032
Fig. 13
Definition of Uinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Uinh
相關PDF資料
PDF描述
CK1501-7PD6B1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-7PD9T 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-9EPD8B1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-9ERD0TB2 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
CK1501-9ERD3TB1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
CK1501-7R 功能描述:EURO-CASSETTE 150W 15V RoHS:否 類別:電源 - 外部/內部(非板載) >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流(最大):24 VDC @ 50A 輸出 - 2 @ 電流(最大):- 輸出 - 3 @ 電流(最大):- 輸出 - 4 @ 電流(最大):- 功率(瓦特):1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H(110mm x 231mm x 156mm) 包裝:散裝 電源(瓦特)- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH
CK1501-9ER 制造商:Power-One 功能描述:DCDC - Bulk
CK1507 制造商:Lorlin Electronics Ltd 功能描述:
CK1508 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GENERAL ELECTRICAL & MECHANICAL SPECIFICATION
CK1509 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GENERAL ELECTRICAL & MECHANICAL SPECIFICATION
主站蜘蛛池模板: 连南| 栖霞市| 贞丰县| 弥勒县| 海南省| 绥德县| 青龙| 苗栗县| 时尚| 邵阳县| 蚌埠市| 石家庄市| 济宁市| 神池县| 积石山| 西安市| 青州市| 定西市| 黄山市| 泸西县| 拜泉县| 上思县| 康平县| 彭州市| 略阳县| 大石桥市| 海伦市| 泰顺县| 石首市| 深圳市| 林周县| 水富县| 永登县| 中方县| 方城县| 永春县| 肥乡县| 尼勒克县| 白河县| 弥勒县| 锡林郭勒盟|