- 您現在的位置：買賣IC網 > PDF目錄379920 > CMM1530-LC-00T0 (Electronic Theatre Controls, Inc.) 1.85 to 1.91 GHz 3.0V, 30 dBm, PCS/PCN LCC-8 Power Amplifier PDF資料下載
參數資料
| 型號： | CMM1530-LC-00T0 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 1.85 to 1.91 GHz 3.0V, 30 dBm, PCS/PCN LCC-8 Power Amplifier |
| 中文描述： | 1.85至1.91 GHz的3.0V，30 dBm的，片/ PCN持有LCC - 8功率放大器 |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 451K |
| 代理商： | CMM1530-LC-00T0 |
3236 Scott Boulevard
Santa Clara, California 95054
Phone: (408) 986-5060
Fax: (408) 986-5095
CMM1530-LC
Features
Operation as Low as 3.0V
38% Linear Power Added Efficiency
+30 dBm Output Power (IS-136 TDMA Mode)
+28.5 dBm Output Power (IS-98 CDMA Mode)
32 dB Gain at Operating Output
Tested Under Digital Modulation
New Low-Cost, Thermally Enhanced,
LCC-8 Package
PHEMT Material Technology
Applications
PCS Handsets
PCS Base Stations
Wireless Local Loop Subscriber Units
CDMAone Handsets
Description
The CMM1530-LC is a linear power amplifier
intended for use in PCS handsets and wireless local loop sub-
scriber units. The amplifier can be biased to meet the require-
ments of PCS-1900, IS-136 (TDMA), IS-98 (CDMA) or DCS-
1800 systems. It is a member of Celeritek’s new
Triniti DX
Pro
family of 3V power amplifier MMICs.
Absolute Maximum Ratings
Parameter
Rating
Drain Voltage (+Vd)
+5.5 V*
Drain Current (Id)
1.8 A
RF Input Power
3 dBm*
DC Gate Voltage (-Vg)
-3.0 V*
The CMM1530-LC is packaged in a low-cost, space
efficient, LCC-8 package that provides excellent electrical sta-
bility and low thermal resistance. The part requires minimal
external circuitry for bias and matching to reduce space and
cost.
This device is unconditionally stable under all source
and load impedances.
1.85 to 1.91 GHz
3.0V, 30 dBm, PCS/PCN
LCC-8 Power Amplifier
Advanced Product Information
November 2002
(1 of 4)
Ground Tab
Vg2
1
Vd1
4
Vg1
2
RF IN
3
7
RF OUT/Vd3
8
Vg3
5
Vd2
6
RF OUT
/
Vd3
Ground Tab
Functional Block Diagram
Parameter
Power Dissipation
Thermal Resistance
Storage Temperature
Rating
5 W
20°C/W
-65°C to +150°C
Parameter
Operating Temperature
Channel Temperature
Soldering Temperature
Rating
-40°C to +90°C
150°C
260°C for 5 Sec.
Recommended Operating Conditions
Parameter
Drain Voltage (+Vd)
Typ
3.0 to 4.2
Units
Volts
Parameter
Operating Temperature (PC Board)
Typ
-30 to +80
Units
°C
* Max (+Vd) and (-Vg) under linear operation. Max potential difference across the device at 1dB gain compression point (2Vd+ |-Vg|) not to exceed the minimum breakdown voltage (Vbr) of +12V.
Application Information
The CMM1530-LC is a three stage amplifier that requires
a positive and a negative supply voltages for proper operation.
It is essential when turning on the device that the negative sup-
ply be applied before the positive supply. When turning the
device off, the positive supply should be removed before the
negative supply is removed.
The CMM1530-LC can be operated over a range of sup-
ply voltages and bias points. It is important that the maximum
power dissipation of the package be observed at all times and
that the maximum voltage across the device is not exceeded.
Circuit Design Considerations
Biasing
Negative gate voltages are necessary to set the bias
currents of the three FET stages in the CMM1530-LC. The
first stage gate bias voltage is applied to Vg1 (Pin 2). The sec-
ond stage gate bias voltage is applied to Vg2 (Pin 1), while the
third stage FET gate bias is applied to Vg3 (Pin 8). It is desir-
able to use one or more DACs (digital to analog converters)
along with appropriate divider networks, in order to adjust the
quiescent currents to within 10 mA of the target values. As an
example, for CDMA applications the target quiescent current
of the third FET is 85 mA, while those for the second and the
first FETs are 45 and 15 mA, respectively. The total quiescent
is 135 mA. It is also recommended that the quiescent currents
be set in the following sequence: the third stage FET is set
first, followed by the second stage FET, followed by the first
stage FET. The negative supply voltages control the quiescent
currents through each of the FETs and, therefore, control the
output power, adjacent channel power ratios, and the currents
at the full output power.
The positive supply voltages are applied to Pins 4, 5, 6
and 7.
– Continued on Page 2 –
相關PDF資料 |
PDF描述 |
|---|---|
| CMM1530-LC-00TT | 1.85 to 1.91 GHz 3.0V, 30 dBm, PCS/PCN LCC-8 Power Amplifier |
| CMM2030 | 30 KHZ TO 30 GHZ GAAS MMIC OPTICAL MODULATOR DRIVER AMPLIFIER |
| CMM2030-BD | 30 KHZ TO 30 GHZ GAAS MMIC OPTICAL MODULATOR DRIVER AMPLIFIER |
| CMM2305 | 800 TO 2700 MHZ BROAD BAND DRIVER AMPLIFIER |
| CMM2306-AJ-000T | Broadband Driver Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CMM1530-LC-00TT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.85 to 1.91 GHz 3.0V, 30 dBm, PCS/PCN LCC-8 Power Amplifier |
| CMM-15-R | 功能描述:數字萬用表 REORDER 685-CMM-17 RoHS:否 制造商:Tektronix 產品:Multimeters 類型:Bench 準確性:0.04 % 電壓范圍:2 V to 2 kV 電阻范圍: 電容范圍: 顯示計數: 頻率:10 Hz to 45 Hz, 850 Hz to 1 MHz 測距: 真均方根值: 數據保持: |
| CMM-15-R-NIST | 功能描述:鉗型萬用表及配件 RO 685-CMM-17-NIST RoHS:否 制造商:Fluke 準確性:2 % 測距:400 A |
| CMM1631-SM | 制造商:MIMIX 制造商全稱:MIMIX 功能描述:16.0-18.0 GHz 1.5-Watt Power Amplifier |
| CMM1631-SM_0608 | 制造商:MIMIX 制造商全稱:MIMIX 功能描述:16.0-18.0 GHz 1.5-Watt Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。