- 您現在的位置：買賣IC網 > PDF目錄257679 > CP3020-7RDVT (POWER-ONE INC) 3-OUTPUT 148 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | CP3020-7RDVT |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 3-OUTPUT 148 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE P01, MODULE |
| 文件頁數： | 8/9頁 |
| 文件大小： | 385K |
| 代理商： | CP3020-7RDVT |
Industrial Environment
DC-DC Converters >100 Watt
P Series
Edition 4/6.99
7/8
MELCHER
The Power Partners.
Pr
eliminar
y
Isolation
The electric strength test is performed as factory test in accordance with IEC/EN 60950 and UL 1950 and should not be
repeated in the field. Melcher will not honour any guarantee claims resulting from electric strength field tests.
Table 3: Isolation
Characteristic
Input to
Output to Output to Auxiliary 1 Auxiliary 1 Auxiliary 1
Unit
case
output(s)
case
output(s)
to input
to case
to output
Electric
Required according to
1.5
3.0 2
0.5
-
3.0 2
0.5
kVrms
strength
IEC/EN 60950
2.1
4.2 2
0.7
-
4.2 2
0.7
kV DC
test voltage
Actual factory test 1 s
2.1
4.2 2
1.5
0.5
4.2 2
1.5
0.5
AC test voltage equivalent
1.5
3.0 2
1.1
0.35
3.0 2
1.1
0.35
kVrms
to actual factory test
Insulation resistance at 500 V DC
>300
>100
>300
>100
M
1 Insulated auxiliary circuits, e.g. Out OK output circuit (option D), inhibit on output side (option i).
2 In accordance with IEC/EN 60950 only subassemblies are tested in factory with this voltage.
Installation Instruction
The P series DC-DC converters are components, intended
exclusively for inclusion within other equipment by an in-
dustrial assembly operation or by professional installers.
Installation must strictly follow the national safety regula-
tions in compliance with the enclosure, mounting, creep-
age, clearance, casualty, markings and segregation re-
quirements of the end-use application. See also:
Technical
Information: Installation and Application.
Connection to the system shall be made via the female
connector H15 or H15 S2 (see:
Accessories) according to
Connector pin allocation. Other installation methods may
not meet the safety requirements.
Check for hazardous voltages before altering any connec-
tions.
The DC-DC converters are provided with pin no. 26 (
),
which is reliably connected to the case. For safety reasons
it is essential to connect these pins to the protective earth of
the supply system if required in:
Safety of operator accessi-
ble output circuit.
The Vi input (pin no. 32) is internally fused. This fuse is de-
signed to protect the unit in case of overcurrent and may
not be able to satisfy all customer requirements. External
fuses in the wiring to one or both input pins (no. 30 and/or
no. 32) may therefore be necessary to ensure compliance
with local requirements.
Important: Whenever the inhibit function is not in use,
pin 28 (i) should be connected to pin 32 (Vi–) to enable
the output(s).
Do not open the modules, or guarantee will be invalidated.
Make sure that there is sufficient air flow available for con-
vection cooling. This should be verified by measuring the
case temperature when the unit is installed and operated in
the end-use application. The maximum specified case tem-
perature
TC max must not be overridden.
Ensure that a unit failure (e.g. by an internal short-circuit)
does not result in a hazardous condition. See also:
Safety
of operator accessible output circuit.
Cleaning Agents
In order to avoid possible damage, any penetration of
cleaning fluids is to be prevented, since the power supplies
are not hermetically sealed.
Standards and approvals
All P series DC-DC converters correspond to class I equip-
ment.
They are pending to be UL recognized according to UL
1950, UL recognized for Canada to CAN/CSA C22.2 No.
950-95 and LGA approved to IEC/EN 60950 standards and
have been designed in accordance with these standards
for:
Building in
Basic insulation between input and case, based on
250 V AC or 240 V DC
Double or reinforced insulation between input and out-
put, based on 250 V AC or 240 V DC
Operational insulation between output(s) and case
Operational insulation between the outputs
Operational insulation between option D or i and out-
put(s)
Operational insulation between option D or i and case
The use in a pollution degree 2 environment
Connecting the input to a primary circuit with a maximum
transient rating of 2500 V (overvoltage class III based on
a 110 V primary circuit, overvoltage class II based on a
230 V primary circuit).
After approvals, the AC-DC converters are subject to
manufacturing surveillance in accordance with the above
mentioned UL, CSA, EN and with ISO 9001 standards.
Protection Degree
Condition: Female connector fitted to the unit.
The protection degree of the DC-DC converters is IP 40.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1023RD2I-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| CAT1027UA-25TE13 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT1023SE-30 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT1023ZD2E-42 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| CAT24C322J-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP3020-9R | 功能描述:EURO-CASSETTE 120W 2X 5.1V&12V RoHS:否 類別:電源 - 外部/內部（非板載） >> DC DC Converters 系列:* 標準包裝:1 系列:Quint 類型:隔離 輸入電壓:24V 輸出:24V 輸出數:1 輸出 - 1 @ 電流（最大）:24 VDC @ 50A 輸出 - 2 @ 電流（最大）:- 輸出 - 3 @ 電流（最大）:- 輸出 - 4 @ 電流（最大）:- 功率（瓦特）:1200W 安裝類型:底座安裝 工作溫度:0°C ~ 40°C 效率:- 封裝/外殼:模塊 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包裝:散裝 電源（瓦特）- 最大:1200W 批準:- 其它名稱:277-69722866365-NDQUINT-BAT/24DC/12AH |
| CP3020-9RD | 功能描述:DC/DC CONVERTER 5.1V DUAL 12V 制造商:bel power solutions 系列:Melcher P 包裝:散裝 零件狀態:有效 類型:隔離 電壓 - 輸入:33.6 ~ 75 V 輸出:5.1V，12V，12V 輸出數:3 不同電流時的輸出（最大值） - 1:5.1 VDC @ 17.8A 不同電流時的輸出（最大值） - 2:12 VDC @ 4A 不同電流時的輸出（最大值） - 3:12 VDC @ 4A 不同電流時的輸出（最大值） - 4:- 功率（W）:187W 應用:ITE（商業），鐵路 安裝類型:底座安裝 工作溫度:-40°C ~ 71°C 效率:88% 封裝/外殼:- 大小/尺寸:6.73" 長 x 4.37" 寬 x 0.78" 高（171.0mm x 111.0mm x 19.8mm） 功率（W） - 最大值:187W 認可:cCSAus，CE，TUV 標準包裝:10 |
| CP3020-9RG | 功能描述:POWER SUPPLYDC-DCIN 33.6TO75VOUT 制造商:bel power solutions 系列:* 零件狀態:在售 標準包裝:5 |
| CP3020G | 制造商:Pentair Technical Products / Hoffman 功能描述:Panel, 28.20x18.20 , fits 30.00x20.00, Steel |
| CP30238 | 功能描述:PELTIER MOD 20 X 3.8MM 3.0A INP RoHS:是 類別:風扇，熱管理 >> 熱 - 熱電，Peltier 模塊 系列:- 產品培訓模塊:Thermoelectric Module Product Line 標準包裝:1 系列:CP 外形L x W x H:39.88mm x 39.88mm x 3.33mm 在 Th 時的 Qmax:72.0W @ 25°C 電流 - 最大:8.5A 電壓 - 最大:14.5V 電阻（歐姆）:1.55 在 Th 時的最大溫差:67°C @ 25°C 其它名稱:926-1256 |
發布緊急采購，3分鐘左右您將得到回復。